After car crash and airbag deployment, VW-Audi airbag sensor can by locked (Control unit faulty or deployed) and must be replaced. Even after small accident Airbag sensor will write in internal memory special error message “crash data stored” or “computer fault” and after you need to exchange very expensive sensor to new one. With our VAG Airbag Reset Tool you can reset and repair airbag computer in your office in 1 minute. No need to remove airbag sensor from the car.
Read the rest of this entry »

• 0 Comments

Simple step to light reset service for Renault Laguna. The reset button is located under the speedometer on the instrument cluster.
Switch ignition on.
Switch ignition on.
Press reset button until “spanner” symbol flashes.
Keep button depressed until “spanner” symbol stops flashing and remains
illuminated.
Read the rest of this entry »

• 0 Comments

This Service & Airbag Reset Tool allows you to reset your car’s Airbag Fault Light & Service (Oil Service & Inspection Service) Indicators on VW/Audi/Seat/Skoda manufactured from 1994 to the latest one that using CAN-BUS protocol, please read the Compatible Vehicles for detail models.
Read the rest of this entry »

• 0 Comments

Alfa Romeo, Fiat and Lancia oil service and oil degradation reset tool. Compatible with the latest Fault Tolerant CAN vehicles. Designed to extinguish the oil service light and to show if there is a fault on the CAN bus which is a common problem with some vehicles.

▪ Compatible with latest Fault Tolerant CAN vehicles.
▪ Also compatible with Alfa Romeo Mito, Fiat Punto 05 , Grand Punto & 500.
▪ CAN BUS Fault indicator.
Read the rest of this entry »

• 0 Comments

Instructions:
• Ignition ‘Off’.
• Plug into car socket.
• Select program.
• Ignition ‘On’.
• Press memory key.
• LED ‘Off’ comes on again after approx. 10 seconds.
• Ignition ’Off’ + ‘On’.
• Car display cleared
Read the rest of this entry »

• 0 Comments

Whenever an automatic transmission is replaced, overhauled or individual components are replaced, use this procedure to clear Engine Control Module (ECM, SAE term: Powertrain Control Module, PCM) “Learned Values” to minimize subsequent performance concerns. CAUTION: Failure to follow the procedure below may lengthen the time to readjust the ECM “Learned Values,” potentially resulting in performance concerns.
Read the rest of this entry »

• 0 Comments

This bulletin supersedes TSB 06-40-005 to include a procedure for GDS. CAUTION: Before replacing a transaxle to improve a shift quality condition, follow this procedure to reset and relearn the adaptive learning.
DESCRIPTION: The PCM or TCM contains logic to adjust solenoid duty and line pressure as needed to compensate for normal clutch wear over the life of the transaxle. This bulletin provides the procedures necessary to reset (erase) and “relearn” the PCM/TCM adaptive values. After the following repairs have been completed, the PCM/TCM adaptive values must be reset in order to provide optimum shift quality:
Read the rest of this entry »

• 0 Comments

Common Problems
1. I am having trouble connecting with an ‘02 Audi A4.
This vehicle does pose connection issues with most aftermarket tools. Please continue to retry the connection.
2. I am having trouble getting good data rates on a specific controller.
Audi/VW consolidated sensors into groups. Some sensor groups can update at slower rates then others. Typically, this is text-based sensors on non-critical models like Telephone or Climate control. To resolve this select only those sensors that are important to you until you reach a saturation point for the data throughput.
Read the rest of this entry »

• 0 Comments

The lamp illustrated is an oil level low warning indicator and not a service interval indicator. When the engine oil is at the correct level, this lamp will automatically extinguish. Malfunction Indicator Lamp (MIL) The lamps illustrated above, are Malfunction Indicator Lamps (MIL) and not service interval indicators. When illuminated there is a problem with the vehicle. Refer to manufacturer’s documentation for further information.
Read the rest of this entry »

• 0 Comments

The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
NOTE: These installation instruction show the left fog light begin installed. The same procedure applies to installing the right fog light.
1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.
2. Disconnect the negative cable from the battery.
Read the rest of this entry »

• 0 Comments