This blower motor has undergone some changes in design so the installation procedures have also changed. The original motor was a two piece motor and the wheel was secured with a set screw. GM changed the design to a one piece unit with a fiberglass heat shield and the wheel is pressed on. On some of the models you may need to remove the front cradle bolts so the engine can be rocked forward. This will help keep the valve cover from interfering with the blower motor replacement. On all models; disconnect the negative battery cable.
Read the rest of this entry »

• 0 Comments

The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.
Read the rest of this entry »

• 0 Comments

LIGHT DISARM RESISTORS
The resistors are connected into the wiring at each wheel to bypass the original dampening solenoid so that the Road Sensing Suspension will function without giving the driver a suspension error message on the instrument cluster.

INSTALL RESISTORS
Cut the wires leading to the dampening solenoid on the strut/shock. Connect the wires to the ends of the resistor. (This is an in-line resistor so it does not matter which wire goes in or out.) Tape up both ends with suitable electrical tape to prevent both shorts and corrosion. Tie back out of way with a plastic strap.
Read the rest of this entry »

• 0 Comments

Raise and support vehicle, allowing suspension to hang free.
Remove the wheel.
Disconnect the shock absorber electrical connector.
Support the lower control arm with a jack stand or screw jack in order to relieve the spring load.
Remove the lower shock absorber nut(s) and bolt(s).
Remove the upper mounting nut(s). On some models, the upper shock mounting nuts are located in the trunk behind the trim cover.
Remove the shock from the vehicle. On some models, you may have to compress the shock by hand to remove from the mounting.
Read the rest of this entry »

• 0 Comments

For best results, please read all instructions thoroughly prior to attempting installation of your SIR MICHAEL’S Cadillac taillight kit. SIR MICHAEL’S recommends the use of approved hand, eye and ear safety equipment while performing this installation. If you have any questions concerning the installation of your SIR MICHAEL’S Cadillac taillight kit.
NOTE: Any part that is modified and/or painted are non returnable.
Read the rest of this entry »

• 0 Comments

1995 ENGINE PERFORMANCE General Motors Corp. Removal, Overhaul & Installation Cadillac; Concours, DeVille, Seville
* PLEASE READ THIS FIRST * CAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION section before disconnecting battery.
Read the rest of this entry »

• 0 Comments

Motor vehicle theft is a serious problem in many parts of the world. In the United States, the annual loss from car theft is over $4 billion. The Automotive Information Council reports that over one million motor vehicles are stolen in the U.S. each year. That’s one motor vehicle theft every 31 seconds.
Read the rest of this entry »

• 0 Comments

Removal & Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures.€ 2. Remove the axle-to-wheel hub retainer nut and washer.€ 3. Remove the parking brake shoes. WARNING Do not use a hammer to separate the outboard CV-joint from the hub. Damage to the threads and internal CV-joint components can result.€ 4. Press the outboard CV-joint until it is loose from the hub.€ 5. Remove and discard the toe link-to-wheel knuckle nut. WARNING Do not damage the boot while separating the toe link from Read the rest of this entry »

• 0 Comments

The GMRC-03 is designed to be used in Cadillac’s that do not have Onstar or amplified systems. It will retain the warning chimes that are lost when the factory radio is removed. The GMRC-03 will also provide a 12 volt switched accessory wire for proper radio operation. *Note: The GMRC-03 can be used in Cadillac’s that come with a factory amplifier; however the factory amplifier must be bypassed and the speaker wires on the GMRC-03 must not be used. Running new wires to the speakers is recommended. If the Cadillac also has Onstar, that feature will be lost.
Read the rest of this entry »

• 0 Comments

The installation instructions step:
1. Disconnect the negative battery cable! Loosen two hose clamps and remove the air intake tube. Separate the intake tube from the plastic clamp on the upper radiator hose. (If equipped).
2. Using a 10mm socket, remove the three nuts that hold the throttle body to the intake manifold.
3. Using a 4mm socket, remove the three studs that go thru the throttle body into the intake manifold.
Read the rest of this entry »

• 0 Comments