The tire pressure warning system informs the driver if it detects a low tire pressure. When the tire pressure warning system detects low tire pressure in any of the 4 wheels which affects safe driving, the tire pressure warning light comes on. Tire pressure warning system is controlled by the Brake Actuator Assembly (skid control ECU). When the tire pressure reset switch is pushed, the tire pressure warning light goes off.
Read the rest of this entry »

• 0 Comments

This manual was written to help owners of /2 BMW motorcycles to service their bikes and keep them in running condition. When these motorcycles were made, they had very different electrical requirements to motorcycles today, and used equipment which today’s owner may not fully understand. Doug and Kees hope that this manual is useful to owners of these motorcycles and that it will help owners keep their bikes where they belong – on the road.
Read the rest of this entry »

• 0 Comments

MyGIGо Multimedia System with GPS Navigation combines satellite radio, DVD playback, GPS navigation and hands-free communication in one powerful package. Voice activation and touch-screen sensitivity makes it extraordinarily easy to use on the road. A 30GB hard drive provides space for up to 4,500 audio files and up to eight photo or graphic files, which can be easily downloaded from CDs or from the integrated USB port. Turn-by-turn navigation instructions are enhanced by SIRIUS Satellite Radio[2] real-time traffic warnings. One easy way to remember MyGIG’s navigation features is the acronym TRIP:
Read the rest of this entry »

• 0 Comments

The AS-100 Anti-skid Drive System is intended for use by the professional aircraft maintenance technician. Use by consumers or other unqualified personnel is not recommended.
Notes:
1. The 4 wheel anti-skid system installed on the Falcon 10 & 50 and others requires the use of 4 Drive Motors with 4 PN AS-300-101 axel adapters.
2. The Messier-Bugatti anti-skid system installed on the Falcon 900 requires the use of the 6 Drive Motors with 4 PN AS-300-203 Axel Adapters, 2 P/N AS-300-204 Axel Adapters.
Read the rest of this entry »

• 0 Comments

There are some steps for upgrade the radio on BMW E34:
I. In this upgrade we address the inadequacies of the factory bass system
and underpowered factory amp. Stock systems are not equipped with subwoofers. Therefore, the best first investment is to add one to the existing system. To add a subwoofer to the factory system we need an amplifier to power it. We have a several choic- es here, depending on budget. The least expensive alternative would be to use a single 310rs.2 along with a P450 amplifier. Powering the new sub- woofer with any a/d/s/ P-series amplifier will allow use of the optional AC502 bass level controller for up-front bass level adjustment.
The next step would be to replace the under per- forming front speaker system with the 235is set which would be mounted in stock front locations. As in most BMW models, factory speaker positions are determined by stylists, not acousticians. As such, we recommend upgrading the 3-way stock system with a 2-way system.
Read the rest of this entry »

• 0 Comments

This Borla Performance Rear Section Exhaust System (Part number 11750) has been designed for 2005 Ford Mustang GT equipped with a 4.6L V-8 engine and automatic or manual transmissions. Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary equipment, tools and experienced personnel needed for proper installation, should perform the installation of this system. However, if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under car safety pre- cautions including eye protection.
Read the rest of this entry »

• 0 Comments

Congratulations on your purchase of the AWE Tuning Exhaust System for the 00-> VW Golf/Jetta/New Beetle with 1.8T or VR6 engine. Exquisite build quality with industry leading performance distinguishes this exhaust system from all others. Our system also features complete T304 Stainless Steel construction, including the internal parts of the muffler. Installation of this exhaust can be completed on jack stands or ramps. Never work under a vehicle only supported by a jack. If you do not feel comfortable installing this system yourself, contact a local professional for installation.
Read the rest of this entry »

• 0 Comments

The Edelbrock Nissan 350Z Performer EFI Nitrous System (Part Number 71007) is designed for 2003-Later Nissan 350Z vehicles equipped with stock 3.5L engines that utilize the returnless style fuel system. Horsepower and torque increases can vary with equipment upgrades and modifications.
The system utilizes one nozzle that is installed in the intake boot just after the MAF (mass air sensor) filter and before the throttle body. The additional fuel needed is supplied by the vehicle’s standard fuel system. This system has been designed with some flexibility as to where certain components can be located to allow easy installation on vehicles with upgraded or modified equipment . The solenoid bracket is designed to be manipulated (bent, cut, twisted, etc.) and the electrical components have properly sized and ample lengths of wire.
Read the rest of this entry »

• 0 Comments

Borla Performance Cat-Back ™ Exhaust System Installation
1. Place a clamp over the expanded end of the front muffler assembly and set it into position as shown in figure 4 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.
2. Place a clamp over the expanded end of the rear muffler assembly and set it into position as shown in figure 5. Do Not tighten the clamps.
3. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.
Read the rest of this entry »

• 0 Comments

Removal of Original System
1) Start under the vehicle. Remove the band clamp that holds the stock system to the turbo by loosening the bolt and prying the clamp loose. Save the band clamp for reuse.
2) Cut the original system just behind the muffler and next to the front cross member.
3) Spray the stock hangers with aerosol lube and pry the system from the rubber mounts. Leave the rubber mounts attached to the truck for re-use.
4) Remove the old system.
Read the rest of this entry »

• 0 Comments