For both front and back bowtie make sure to clean surface with rubbing alcohol before applying replacement bowties to the car.
Front Bowtie: Reach both hands underneath the factory bowtie housing (whole chrome piece) on each side. Feel around for the two clips on the back of the bowtie housing. Pull both of the clips down and forcefully pull/wiggle the bowtie housing out. Flip over the housing and poke out the gold bowtie through the back using a flat head screwdriver and the four holes on the back of the bowtie housing unit. Clean the area and replace with the DefenderWorx Bowtie. Snap the bowtie housing back into place on the grill and enjoy your new DefenderWorx Replacement Bowtie.
Read the rest of this entry »

• 0 Comments

Catching both the automotive industry and the American motoring public by surprise, Ford released the new Mustang in April, 1964 to unprecedented success. Its smaller, two door profile along with its long hood/short rear deck design made a lasting impression on everyone who saw it. Stunned by the sales numbers the Mustang was racking up, it took until 1967 Read the rest of this entry »

• 0 Comments

This Borla Performance Exhaust System (part number 11774 & 11775) has been designed for 2010 Chevrolet Camaro equipped with a 6.2L V-8 engine with an automatic or manual transmission. Borla Performance Exhaust System (part number 11776) has been designed for 2010 Chevrolet Camaro equipped with a 3.6L V-6 engine with an automatic or manual transmission.
Read the rest of this entry »

• 0 Comments

The Edelbrock E-Force Competition Air Intake System is intended only for use on 2010-2011 Chevrolet Camaro SS’ that have been equipped with the Edelbrock E-Force Competition Supercharger System. This intake is not compatible with naturally aspirated cars, nor with those using a different supercharger. While this system can also be used with the #1597/1598 street legal packages, installation may violate emission regulations in some areas.
Read the rest of this entry »

• 0 Comments

This HowTo will go into the requirements, tools and procedure to remove and install a CAM on a Dodge 4.7 liter Engine.

Pre-Install Tips
Step 1
• Set TOP Dead Center (TDC) So V8 marks on both Sprockets are at 12 O’clock!/Crank balancer TDC mark should be aligned to TDC mark on block!
Step 2
• Mark One Link on Chain at (TDC) V8 marks with paint Pen!
Step 3
• Zip Tie Chain to Cam Sprockets (Through two holes in left sprocket and one hole in right sprocket)! Note: Do this after loosening sprocket bolt but before removing bolt and sprocket!
Read the rest of this entry »

• 0 Comments

Thanks again for purchasing your new 304 polished stainless steel Pypes Performance Exhaust (PPE) 2010 Camaro Headers. Please be sure to confirm hardware, gaskets and instructions were included in the kit before beginning installation. Work Safe: When supporting a vehicle on jack stands, be sure the ground surface is level and solid, hot Read the rest of this entry »

• 0 Comments

This Z3 Hardtop Use & Install manual serves as a supplement to the owner’s manual for your vehicle. Keep it safely together with your other vehicle papers. Please refer to the owner’s manual for your vehicle or to the corresponding supplementary owner’s manual for on other items of vehicle. Your BMW service centre you with any queries engineering and high level of quality of BMW equipment is ensured therefore possible that discrepancies occur between this supplementary uni in! on-”* *^o er your vehicle. We cannot exclude a!! errors either and in this we would ask for your understanding so that no legal claims may be brought deriving from the data, illustrations and descriptions in this Read the rest of this entry »

• 2 Comments

The information below documents the procedure I used to install the Hella Micro DE fog lamps on Saab 92-X.
Disclaimer: This information is provided as a reference and the author assumes no responsibility for any damage that may result from this modification to your car.
1. Prep: I started by purchasing the stock Subaru Fog Lamp Relay and Fog Lamp Switch. Since the car is pre-wired for the factory fog lamps, this allows you to use the existing wiring for the installation of the Hella fog lamps.
The part numbers for the parts are: The Fog Lamp Relay is B48 in the diagram below and is the 3rd relay from the bottom. The location will be the only one empty. The Fog Lamp switch is connected to B160, which will be right behind the switch location. By removing the change holder, I was able to install the relay and switch, and plug the connector into the back of the switch without removing the lower dash panel, but it requires some patience.
Read the rest of this entry »

• 0 Comments

Start by removing the factory pillar. This is done by pulling down the rubber door gasket and removing the two screws in the handle area of the pillar, tip the top towards the steering wheel to get it out. You have to use a little force to get it free of the dash.
Though the gauge pod is intended to be used as a replacement for the factory pillar, we suggest cutting the handle off of the factory pillar and using the gauge pod as a cover. This is so that the backs of the gauges will not be visible through the windshield after installation.
Read the rest of this entry »

• 0 Comments

This Borla Performance Stainless Steel Long Tube Header System (Part Number 17249) has been designed for the Chevrolet Camaro equipped with a 6.2L V-8 engine with an automatic or manual transmission.
Original Manifold System Removal
1. Disconnect the battery from the vehicle as recommended by the vehicle manufacturer.
2. Remove the oil filler cap and the under hood engine cover.
Read the rest of this entry »

• 0 Comments