1. For the Dakota: Remove bumper, retaining all OEM fasteners for reinstallation.
Proceed to Step 2.
For the Durango: Prior to removing the bumper, cut and remove the center portion of the bumper and air dam as shown in the photo below. Retain the cut out section of the air dam to fabricate an air deflector in Step 8. Remove the remaining bumper assembly, retaining all OEM fasteners for reinstallation.
2. Clamp the driver-side mount plate to the outside of the driver-side vehicle frame. Make sure the mount alignment tab fits up against the back of the vehicle frame front plate, and the front and rear plate stiffeners are snug against the bottom of the frame. When positioned correctly, mount plate holes align near the center of the vehicle frame.
Read the rest of this entry »

• 0 Comments

These instructions are based on my experience with removing and cleaning the throttle body and from information obtained from the 2000 Durango Factory Service Manual. They were originally my notes for use when I have to do it again. They are as complete and detailed as I can make them, however they are provided for informational purposes only and you should follow or use them at your own risk! Other year models may be different; other engines ARE different. If something on yours seems different, it may well be! Use your head and be careful.
Read the rest of this entry »

• 0 Comments

This undercarriage fits all models listed but the cross member connection will vary. Refer to step “a” for the 1987–96 Dodge Dakota, 1997–03 Dodge Dakota Sport, 1997–03 Dodge Dakota SLT Extended Cab and 1998–03 Dodge Durango SLT models. Refer to step “b” for the 1997–04 Dodge Dakota and 1998–03 Dodge Durango.
Read the rest of this entry »

• 0 Comments

This manual is intended for the installation of the Powerdyne Supercharger kit, Part Number K10513 on the Dodge 318 or 360 C.I. motors, model years 1999–2000 This kit is designed to be 50 state smog legal and as of the writing of this manual C.A.R.B. (California Air Resources Board) exemption is pending. This kit already complies with Federal EPA memorandum 1A, making it smog legal in 49 states, providing your states pollution laws do not supercede EPA memorandum 1A.
Read the rest of this entry »

• 0 Comments

Select the Navigation key on the SETTINGS screen 3 Select the Tracking On Off key 4 Select the On key 11 16 How do I adjust the display REVIEW COPY 2005 nav Navigation System OM USA English nna 07 10 04 debbie GPS INFORMATION DISPLAY The following GPS information will be displayed on the screen latitude longitude altitude signal reception and satellite locations 1.
Read the rest of this entry »

• 0 Comments

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
TOOLS REQUIRED: #2 Phillips screwdriver, 5/64” drill bit, drill, marking pen.
PARTS INCLUDED: Pro.Fit VSMTM, instructions, two (2) #10×5/8” screws.
LOCATION: Lower right corner of radio, below the radio.
Read the rest of this entry »

• 0 Comments

Included with your Poweraid Spacer is a sticker with a California Air Resources Board (C.A.R.B.) Executive Order (EO) number. This sticker must be placed in plain view inside of the engine compartment. Failure to do so may prevent you from passing a smog inspection.
Installation Procedure:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner assembly.
3. Using 1/2” socket, remove (4) 5/16” bolts attaching throttle body to manifold.
4. Lift throttle body.
Read the rest of this entry »

• 0 Comments

WHEN INSTALLING THIS EXHAUST SYSTEM MAKE SURE TO USE PROPER SAFETY PRECAUTIONS. USE JACK STANDS WHEN UNDER TRUCK, SET PARKING BRAKE, BLOCK TIRES AND USE SAFETY GLASSES AND GLOVES. DO NOT WORK WITH HOT PIPES!
SUGGESTED TOOLS:
9/16” SOCKET & WRENCH, 15MM SOCKET, ―’ SOCKET & WRENCH, HACKSAW, JACKSTAND,WD-40

DO NOT REMOVE THE STOCK HEADPIPE.CUT 1 ―” IN FRONT OF STOCK MUFFLER. FOR AN EASIER REMOVAL OF THE STOCK EXHAUST CUT THE FACTORY TAILPIPE BEHIND THE MUFFLER. LEAVE ALL FACTORY RUBBER GROMMETS IN PLACE. SPRAY WD-40 ON ALL RUBBER STOCK HANGERS FOR EASIER REMOVAL.
Read the rest of this entry »

• 0 Comments

Remove dirt with a vacuum cleaner or broom Appearance and care 7 5 REVIEW COPY 2005 Xterra xtr Owners Manual USA English nna 01 26 05 tbrooks MEMO 7 6 Appearance and care 8 Maintenance and do it yourself Maintenance requirements 8 2 General maintenance 8 2 Explanation of general maintenance items 8 2 Maintenance precautions 8 5 Engine compartment check locations 8 6 Engine cooling system 8 7 Checking engine coolant level 8 7 Changing engine coolant 8 8 Engine oil 8 8 Checking engine oil level 8 8 Changing engine oil 8 9 Changing engine oil filter 8 10 5 speed automatic transmission fluid 8 11 Power steering fluid 8 11 Brake and clutch fluid 8 11 Brake fluid 8 12 Clutch fluid 8 12 Window washer fluid 8 12 Window washer fluid reservoir 8 12 Battery
Read the rest of this entry »

• 0 Comments

The BMW 3 Series (E46) Service Manual: 1999-2005 is a comprehensive source of service information and specifications for BMW 3 Series from 1999 to 2005. The aim throughout this manual has been simplicity, clarity and completeness, with practical explanations, step-by-step procedures and accurate specifications.
Read the rest of this entry »

• 0 Comments