Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
Read the rest of this entry »

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
Read the rest of this entry »

• 0 Comments

Neon Front Door Instructions:
1. Using a pick tool pry open the screw cover behind the interior door release lever and remove the screw.
2. Remove the screws in the armrest pocket and at the top of the door near the front.
3. For models with manual windows use a window crank removal tool to disengage the pin securing the window
crank and pull the window crank from the door. The triangle shaped piece that houses the side mirror
adjustment control lever will need to be pulled away from the door. Using a panel removal tool gently pry
the bottom of the plastic away from the door to release the fasteners and let it hang by the mirror control cables.
Read the rest of this entry »

• 0 Comments

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2006 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments

Procedures of LED Mirror-Beam installation on Dodge Charger/Magnum.
Removing the Side Mirror:
NOTE: This product can not be used if your vehicle is equipped with break-away mirrors.
1. Remove the driver side door panel from the vehicle (Fig. 1). To remove the door panel: Remove the 5 caps labeled “A” (Fig. 1). Take a pen or other object and depress the center of the cap. This will disengage the cap so it can be removed, then remove the Phillips head screws under the two covers labeled “B”. Remove the 3 clips from inside the window track (Fig. 1). Remove the 4 Phillips head screws from the bottom of the door panel. Unhook the door opener rod and unplug the 3 electrical connectors behind the door panel.
Read the rest of this entry »

• 0 Comments

There are some steps for upgrade the radio on BMW E34:
I. In this upgrade we address the inadequacies of the factory bass system
and underpowered factory amp. Stock systems are not equipped with subwoofers. Therefore, the best first investment is to add one to the existing system. To add a subwoofer to the factory system we need an amplifier to power it. We have a several choic- es here, depending on budget. The least expensive alternative would be to use a single 310rs.2 along with a P450 amplifier. Powering the new sub- woofer with any a/d/s/ P-series amplifier will allow use of the optional AC502 bass level controller for up-front bass level adjustment.
The next step would be to replace the under per- forming front speaker system with the 235is set which would be mounted in stock front locations. As in most BMW models, factory speaker positions are determined by stylists, not acousticians. As such, we recommend upgrading the 3-way stock system with a 2-way system.
Read the rest of this entry »

• 0 Comments

Subwoofer Installation 1. Find the fuse block under the hood and open the fuse box cover.
2. Using a 13mm socket and ratchet loosen and remove the fuse box power supply nut.
3. Connect the ring terminal of the power harness to the fuse box power lug and retighten the nut.
4. Route the wire toward the rubber grommet in the fire wall where the hood release cable passes through securing with wire ties where needed.
Read the rest of this entry »

• 0 Comments

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2008 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments

Installation: 2005 Dodge Charger or Magnum
1. Remove the 2 plastic covers that protect the front area under the hood (Fig. 1). They snap into or out of the vehicle.
2. Remove the 2 bolts that hold the hood latch assembly on and set it aside (do not disconnect the cables). Unplug the horn wire and place the wire out of the way (Figs. 1 & 2).
3. Mount speaker to bracket (Fig. 3).
4. Remove all the plastic rivets from the top of the front of the body of the vehicle, then pull the body toward the front of the vehicle (the body is flexible). Slide the 2 U-Nuts onto the support braces (Fig. 4) and place the bracket (with siren attached) on top of the U-Nuts. The front “ears” of the bracket rest on the two U-Nuts which clip onto the support braces (Fig. 4). The rear of the bracket will mount behind the hood latch assembly using the hood latch’s mounting hardware (Fig. 2).
Read the rest of this entry »

• 0 Comments

Monster Exhaust System Installation:
1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post.
2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground.
Read the rest of this entry »

• 0 Comments