Read all instructions before starting any work.
1. Remove the O.E. muffler and tail pipes only. Any pipe ahead of the OE muffler should be retained. Lubricate the rubber isolators and fasteners with WD-40, or similar product, to aid in removal.
2. Place a 3″ band clamp on the inlet of DynoMax front pipe 51061 and install. Slightly tighten the inlet band clamp.
3. Install DynoMax Ultra Flo SS muffler 17273. Place a 3″ saddle clamp on the muffler inlet connection and finger tighten. Rotate the muffler to a 450 angle with the top toward the drive shaft. Please see system diagram.
Read the rest of this entry »

• 0 Comments

Banks Monster® Exhaust System Dual-Tip 2007-2008 Dodge 6.7L Cummins ISB Pickup Trucks Including Mega Cab Owners Manual.
1. For ease of installation of your Banks system, familiarize yourself with the procedure by reading the entire manual before starting work.
2. The general assembly diagram (Figure 1) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction.
Read the rest of this entry »

• 0 Comments

Monster Exhaust System Installation:
1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post.
2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground.
Read the rest of this entry »

• 0 Comments

This Borla Performance Exhaust System (part number 11774 & 11775) has been designed for 2010 Chevrolet Camaro equipped with a 6.2L V-8 engine with an automatic or manual transmission. Borla Performance Exhaust System (part number 11776) has been designed for 2010 Chevrolet Camaro equipped with a 3.6L V-6 engine with an automatic or manual transmission.
Read the rest of this entry »

• 0 Comments

Disconnect the negative battery cable before removal of OEM exhaust. This will allow the computer to reset and recognize the new exhaust. Lay out the exhaust on the floor so it looks like the drawing and compare parts with manual.
1. To remove the stock exhaust remove it from in front of the stock muffler. DO NOT REMOVE STOCK HEADPIPE. Disengage the welded hangers using WD-40 from the OEM rubber grommets. Do not damage or remove the rubber grommets as you will re-use them to mount your new system.
2. Install head pipe #A onto your existing stock front pipe and attach with clamp #J. Use a jack stand to support the converter. Insert welded hanger into rubber grommet.
Read the rest of this entry »

• 0 Comments

This Borla Performance Rear Section Exhaust System (Part number 11777 & 11778 ) has been designed for 2010 Ford Mustang GT equipped with a 4.6L V-8 engine and automatic or manual transmissions. Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary equipment, tools and experienced personnel needed for proper installation, should perform the installation of this system. However, if you decide to perform the installation, we recommend someone should help you. Ensure the installer uses all under car safety precautions including eye protection. Please take time to read and understand the following… By installing your Borla Read the rest of this entry »

• 0 Comments

Note on Sport Model Trucks – This light bar will not mount correctly on sport model trucks without realigning the bumper. TRUCKS WITH FACTORY TOW HOOKS
1. Temporarily remove the factory tow hooks and set them aside along with the bolts.
2. Position your KC light bar so the brackets will sandwich between the tow hooks and the frame. ( NOTE – The light bar must be rolled into Bumper place by inserting the lower end of the brackets into the opening first Bolts and then rolling it up into place.)
Read the rest of this entry »

• 0 Comments

This manual contains the pre-installation, assembly and installation for dual player headrest video on Toyota Prius 2010.
Pre-installation Precaution
1. Use Seat and Floor Protectors to avoid damage to surfaces.
2. If the vehicle is equipped with an Anti-theft radio, the radio code must be written down prior to disconnecting the battery cable. The code must be re-entered when the negative battery cable is reinstalled. Disconnecting the battery
Figure may cause certain vehicle settings to be lost. Manufacture’s recommendations for the battery B3 removal should be followed. Disconnecting the battery is recommended.
Read the rest of this entry »

• 0 Comments

This manual is divided into different areas to assist you with your installation and operation of your braking unit. We strongly suggest that you write down the kit and serial numbers of your unit in the spaces provided and retain this manual for any future reference
Kit Contents
2033135 – 1988-1998 Dodge Cummins 12V Exhaust Brake Kit
1 1230030 Vacuum Control Kit (w/ Micro Switch)
1 1230335 Vacuum Spool Valve Kit
1 2133030 Exhaust Brake
Read the rest of this entry »

• 0 Comments

Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a significant period of time for the chemical to lubricate the threads before attempting to disassemble.
1. On each exhaust pipe behind the catalytic converter, unbolt the clamp (figure 1) using a 15mm socket. Unbend the metal tab (figure 2) on each pipe.
2. Remove (4) cross-brace support bolts using 15mm socket (figure 3). Place hardware to the side.
3. Lubricate all the hangers and rubber isolators.
4. Using a muffler stand or an additional person to hold the rear muffler into position, remove the hangers from the rubber isolators (figure 3) and at each rear muffler.
Read the rest of this entry »

• 0 Comments