Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended Read the rest of this entry »

• 1 Comment

Caution!!! Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use a hoist or hydraulic lift to facilitate the installation of your new Borla Performance Cat-Back ™ Exhaust System. Taking all under car safety precautions, lift the vehicle using a hoist or hydraulic lift. Once this has been done, you may begin the removal of your old exhaust system from your vehicle. Note: Before removing the original exhaust system from your vehicle, please compare the parts you have received with the bill of materials provided on the previous page to assure that you have all the parts necessary for the installation of your new Borla Performance Cat-Back ™ Exhaust System.
Read the rest of this entry »

• 0 Comments

Open the liftgate and remove the upper liftgate trim panel.
Remove the right (passenger’s side) D-pillar trim panel.
Install audio/visual display to the right D-pillar trim panel as shown.
Remove the lower liftgate trim panel.
Remove the right C-pillar trim panel.
Remove the right inner quarter trim panel.
Remove the rear fascia and place it on a protected surface.
Read the rest of this entry »

• 0 Comments

1. Disconnect the negative battery cable. Loosen the hose clamp on air cleaner box lid. Twist and remove breather hose from air cleaner box lid. 2. Unhook the two air cleaner lid latches on front of box. 3. Remove the air cleaner box lid by sliding it forward, and then up, and out of the factory intake tube. 4. Remove factory air filter from air cleaner box. 5. Remove, and set aside the oil filler cap. Use caution not to drop anything into engine while cap is off. 6. Carefully lift up on the engine cover (it is held in place by grommets, no bolts) to access the hose clamp Read the rest of this entry »

• 0 Comments

Entertainment Systems – FLO TV
FLO TV`99 service provides a superior mobile TV experience that is available to over 200 million people in 105 major U.S. markets. Many key transportation corridors will be covered by the FLO TV network and coverage will extend to 95 percent of where these Americans live, work, drive. That means that you can receive 24/7 programming to keep your entire crew entertained, regardless of the trip duration. Even if you`ve got to keep your eyes on the road, you can enjoy listening to 60 Minutes from CBS Mobile or the
Read the rest of this entry »

• 0 Comments

Subwoofer Installation 1. Find the fuse block under the hood and open the fuse box cover.
2. Using a 13mm socket and ratchet loosen and remove the fuse box power supply nut.
3. Connect the ring terminal of the power harness to the fuse box power lug and retighten the nut.
4. Route the wire toward the rubber grommet in the fire wall where the hood release cable passes through securing with wire ties where needed.
Read the rest of this entry »

• 0 Comments

Detailed Instructions
1 Check off all items against Snorkel Kit List.
2 Remove guard liner, front rubber and windscreen washer reservoir.
3 Tape Template together accurately on gridline 17. Cut down grid line 28 to mark.
4 Place the Airflow Template supplied on the guard, ensuring the guard crease line are followed exactly. The top guard edge line is a guide only as it will vary slightly between pre and post 1997 cherokee’s.
5 Tape over the sites of all hole points to protect the guard. Locate holes as indicated and mark with centre punch. Drill the 8mm holes. Be careful of any wires or other obstructions under the inner guard.
Read the rest of this entry »

• 0 Comments

The installation of the AEM ECU on the 1995-1999 Mitsubishi Eclipse Turbo / Eagle Talon Tsi uses the stock sensors and actuators. The base map is automatically installed in the base calibrations directory in the AEMPro directory on your computer.
Full details of the test vehicle used to generate this map can be found in the files notes section. However, while the base map is a good starting point and may save you considerable time and money, it will not replace the need to tune your specific application. It is not intended to be driven aggressively. Ignoring this can and will damage your engine.
Read the rest of this entry »

• 0 Comments

The BMW 3 Series (E46) Service Manual: 1999-2005 is a comprehensive source of service information and specifications for BMW 3 Series from 1999 to 2005. The aim throughout this manual has been simplicity, clarity and completeness, with practical explanations, step-by-step procedures and accurate specifications.
Read the rest of this entry »

• 0 Comments

Why our nitrous system is better:
• A complete 1999-2004 Mustang GT specific nitrous system. Everything is included in this kit for a safe, easy, plug and play installation.
• Adjustable from 75-175 horsepower. Safe enough for stock engines, powerful enough for racing use.
• Uses a custom made Ford fuel rail adaptor. This component gives easy access to the fuel system for nitrous system hook-up, especially the 2003-04 models.
• The 1999-2004 Mustang GT Nitrous System is activated at wide open throttle with advanced electronics that monitor your throttle position sensor (TPS); easy and safe activation.
• Unique nozzle design has “Active Fuel Control™” built in. This feature monitors bottle pressure and when the nitrous system is engaged, it adds or subtracts enrichment fuel so the engine never runs too rich or too lean.
Read the rest of this entry »

• 0 Comments