Introduction: Remove/Install rear sub-frame bushes in Mondeo. Can be used in situ – no need to remove sub-frame from vehicle. Applications: Ford Mondeo 2001, 10/2000 onwards
3.1 Ensure that the vehicle is adequately supported on axle stands before working under the vehicle.
3.2 Although there is no need to remove the sub-frame from the vehicle it will be necessary to lower it to gain access to both sides of the bush housing.
Read the rest of this entry »

• 0 Comments

Removal & Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures.€ 2. Remove the axle-to-wheel hub retainer nut and washer.€ 3. Remove the parking brake shoes. WARNING Do not use a hammer to separate the outboard CV-joint from the hub. Damage to the threads and internal CV-joint components can result.€ 4. Press the outboard CV-joint until it is loose from the hub.€ 5. Remove and discard the toe link-to-wheel knuckle nut. WARNING Do not damage the boot while separating the toe link from Read the rest of this entry »

• 0 Comments

The following procedures for removing the fan clutch gives the factory recommended loosening and tightening directions for the fan hub nut. However, it has been our experience that certain aftermarket parts manufacturers have changed this to enable use of universal fit parts. We recommend trying the factory direction first, then, if the nut doesn’t seem to be moving, reverse the direction. Placing too much load on the water pump snout will break it.
Read the rest of this entry »

• 0 Comments

This set of two tools allows swift removal of the lock plug from many newer Ford and GM glove compartments. The FPR-2 spreads the plastic retaining arms with minimal risk of breakage, pushing out the plug safely. This operation is necessary when obtaining correct code information. Ford, GM, and many European models including Audi, Saab, and VW utilize this mounting method.
Read the rest of this entry »

• 0 Comments

Wiper and Washer System — Front Item Part Number Description 1 W707014-S441 Wiper pivot arm nut 2 17526 Wiper pivot arm (LH and RH) 3 N807391 Wiper pivot arm linkage bolt (3 required) 4 17508A Wiper pivot arm linkage assembly (includes wiper motor) 5 — Wiper motor crank bolt 6 — Wiper motor attachment bolt (3 required) (Continued) 7 17508B Wiper motor 1 W708312 Wiper pivot arm nut 2 17526 Wiper pivot arm Read the rest of this entry »

• 0 Comments

STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
STEP 2: Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio.
Read the rest of this entry »

• 0 Comments

Chevrolet LCT1000–LCT2500, Ford 47RH / 47RE / 48RE, Dodge E4OD / 4R100 Transmission removal, Installation And testing
Removal
Check and record all codes and actions of your transmission before transmission is removed. This will help if you still have problems after installation. Damage to your transmission may have been caused from some other external source.
Read the rest of this entry »

• 0 Comments

The Ford supplied Sierra 4×4 Supplementary Workshop Manual is a “must have” for any owner of one of these cars. The biggest problem can be actually finding one to purchase. I got lucky and managed to get mine direct from a Ford dealer, brand new for Ł8, who was having a clearout. They do appear regularly at autojumbles and it is just a case of keep looking. The manual only covers those items unique to the 4×4 Sierra’s and Read the rest of this entry »

• 1 Comment

For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any pad contacts rotor or if pad is worn to within .03″ (.8 mm) of pad backing.
Removal (”A”, “B”, “C”, “K” & “U” Series)
1. Remove 2/3 of brake fluid from master cylinder reservoir. Raise and support vehicle. Remove wheel. Using “C” clamp, compress caliper piston until it bottoms out in its bore.
Read the rest of this entry »

• 0 Comments

REMOVAL 1. Disconnect the ground cable from battery. 2. Remove the front grille RH and front grille LH. 3. Remove the clips inside the mounting portion of front grille RH and front grille LH. 4. Remove the six clips on the upper part of bumper. 5. Remove the clips, which secure the front bumper to fender. 6. Remove the clips, and turn over the mud guard LH and RH. 7. Remove the three clips in the center, right and left part of Read the rest of this entry »

• 0 Comments