glove box removal ford mondeo search result
This set of two tools allows swift removal of the lock plug from many newer Ford and GM glove compartments. The FPR-2 spreads the plastic retaining arms with minimal risk of breakage, pushing out the plug safely. This operation is necessary when obtaining correct code information. Ford, GM, and many European models including Audi, Saab, and VW utilize this mounting method.
Read the rest of this entry »
For the first time, Ford is using a front-wheel drive in a middle range vehicle. For this reason, the well-proven MTX 75 transmission from the Fiesta/Escort has been modified and adapted to the requirements of the Ford Mondeo. At the same time, a 4×4 version is also offered, in which the MTX 75 transmission is extended, as on the Escort 4×4, by a transfer box. The transfer box in the Ford Mondeo is a new development and effectively transfers the higher torque to the front axle. This brochure describes all new features and modifications implemented on the MTX 75 transmission compared to the MTX 75 transmission of the Escort ‘91 as well as on the MTX 75 4×4 drive concept and vehicle compared to the Ford Mondeo with front wheel drive.
Read the rest of this entry »
Introduction: Remove/Install rear sub-frame bushes in Mondeo. Can be used in situ – no need to remove sub-frame from vehicle. Applications: Ford Mondeo 2001, 10/2000 onwards
3.1 Ensure that the vehicle is adequately supported on axle stands before working under the vehicle.
3.2 Although there is no need to remove the sub-frame from the vehicle it will be necessary to lower it to gain access to both sides of the bush housing.
Read the rest of this entry »
Subject: Starter motor Failure
Model: Ford 2.0 TDCI FWD & 2.4 TDCi RWD/2.0 TDCi FWD
On inspection, the units do not exhibit any manufacturing defects. The premature failure of the unit is due to contamination of the pinion/drive area from metal dust particles produced within the Dual-mass Flywheel, when the clutch wears or becomes overheated. During scheduled servicing, it is recommended that the clutch is checked and if found to be showing signs of wear should be replaced.
Read the rest of this entry »
Removal & Installation WARNING Do not loosen the axle wheel hub retainer until the wheel and tire are removed from the vehicle. Wheel bearing damage will occur if the wheel bearing is unloaded with the weight of the vehicle applied. NOTE Have an assistant press the brake pedal to keep the axle from turning. 1. Before servicing the vehicle, please familiarize yourself with safety procedures. 2. Remove the axle-to-wheel hub retainer nut and washer. 3. Remove the parking brake shoes. WARNING Do not use a hammer to separate the outboard CV-joint from the hub. Damage to the threads and internal CV-joint components can result. 4. Press the outboard CV-joint until it is loose from the hub. 5. Remove and discard the toe link-to-wheel knuckle nut. WARNING Do not damage the boot while separating the toe link from Read the rest of this entry »
1991-1999 Ford Ranger/Explorer/Mountaineer Engine Fan Removal & Installation
24 May
Posted by admin as Ford
The following procedures for removing the fan clutch gives the factory recommended loosening and tightening directions for the fan hub nut. However, it has been our experience that certain aftermarket parts manufacturers have changed this to enable use of universal fit parts. We recommend trying the factory direction first, then, if the nut doesn’t seem to be moving, reverse the direction. Placing too much load on the water pump snout will break it.
Read the rest of this entry »
Wiper and Washer System — Front Item Part Number Description 1 W707014-S441 Wiper pivot arm nut 2 17526 Wiper pivot arm (LH and RH) 3 N807391 Wiper pivot arm linkage bolt (3 required) 4 17508A Wiper pivot arm linkage assembly (includes wiper motor) 5 — Wiper motor crank bolt 6 — Wiper motor attachment bolt (3 required) (Continued) 7 17508B Wiper motor 1 W708312 Wiper pivot arm nut 2 17526 Wiper pivot arm Read the rest of this entry »
STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
STEP 2: Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio.
Read the rest of this entry »
Chevrolet LCT1000–LCT2500, Ford 47RH / 47RE / 48RE, Dodge E4OD / 4R100 Transmission removal, Installation And testing
Removal
Check and record all codes and actions of your transmission before transmission is removed. This will help if you still have problems after installation. Damage to your transmission may have been caused from some other external source.
Read the rest of this entry »
The interior ventilation filter for Acura RDX, TL, TSX, Honda Accord, Civic, CR-V. Interior ventilation filter is located in filter housing behind glove compartment door.
1. Open glove box door. Grasp and pull down on the glove door holding rod located on the right side of the glove box door.
2. Insert a flat-tip screw driver to the glove box door stays and gently apply pressure towards the inside of the door to remove glove box door stays. Swing glove box door downwards.
Read the rest of this entry »
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease