Monster Exhaust System Installation:
1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post.
2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground.
Read the rest of this entry »

• 0 Comments

1. For ease of installation of your Banks Ram-air intake system, familiarize yourself with the procedure by reading the entire manual before starting work. This manual contains 16 pages of copy, illustrations and parts listing. If any pages are missing from this manual please call Gale Banks Engineering immediately for a replacement.
Read the rest of this entry »

• 0 Comments

Banks Monster® Exhaust System Dual-Tip 2007-2008 Dodge 6.7L Cummins ISB Pickup Trucks Including Mega Cab Owners Manual.
1. For ease of installation of your Banks system, familiarize yourself with the procedure by reading the entire manual before starting work.
2. The general assembly diagram (Figure 1) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction.
Read the rest of this entry »

• 0 Comments

This kit will allow you to adapt a Chrysler 392 Hemi engine to all GM transmissions utilizing the Chevrolet bolt pattern. The use of this adapter kit will require a stock length torque converter. (A GM torque converter must be used with this adapter kit. It will not work with a Chrysler torque converter). Your Chrysler starter will bolt into place without any modifications. Reuse your OEM starter bolts.
Read the rest of this entry »

• 0 Comments

Read all instructions before starting any work.
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂” clamps that connect the mufflers to the x-pipe.
Read the rest of this entry »

• 0 Comments

This Borla Performance Exhaust System (part number 11774 & 11775) has been designed for 2010 Chevrolet Camaro equipped with a 6.2L V-8 engine with an automatic or manual transmission. Borla Performance Exhaust System (part number 11776) has been designed for 2010 Chevrolet Camaro equipped with a 3.6L V-6 engine with an automatic or manual transmission.
Read the rest of this entry »

• 0 Comments

Step 1: Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground using a floor jack and jack stands or a (2) two post lift if available and remove the front wheels and tires. Locate the front sway bar and unbolt the lower end link. Do this on both sides of vehicle. Next locate the lower track bar mount on the passenger side of the vehicle and unbolt from axle. (Insert B)
Step 2: Place an index mark on the stock coil and a matching one on the lower coil pocket. This will allow you to replace the coils in the stock location Next locate the upper shock mounts (they are located in the engine compartment) and remove the upper shock hardware. Next remove the 3 nuts from the upper shock mounts. Do this on both sides of vehicle. Now remove the lower shock mounting bolts and remove the shocks by pulling them up through the engine compartment. Do this on both sides of vehicle.
Read the rest of this entry »

• 0 Comments

Congratulations on your purchase of the AWE Tuning Exhaust System for the 00-> VW Golf/Jetta/New Beetle with 1.8T or VR6 engine. Exquisite build quality with industry leading performance distinguishes this exhaust system from all others. Our system also features complete T304 Stainless Steel construction, including the internal parts of the muffler. Installation of this exhaust can be completed on jack stands or ramps. Never work under a vehicle only supported by a jack. If you do not feel comfortable installing this system yourself, contact a local professional for installation.
Read the rest of this entry »

• 0 Comments

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting at the Passenger/Right side-front of the vehicle, remove the front factory body bolt & washer.(not re-used) (Fig 1), From the list above select the Passenger/Right side front mounting bracket and the spacer Block secure to vehicle with (1) 12mm x 150mm Hex Bolt, (1) 12mm Flat Washer, (1) 12mm Lock Washers (Fig 1A). Snug but do not tighten hardware at this time.
3. Next, select the T Bolt from the list of parts above, and place the T Bolt into the opening on the Passenger/Right side bottom front frame rail (Fig 2 shows T Bolt placed into frame rail.
Read the rest of this entry »

• 0 Comments

Borla Performance Cat-Back ™ Exhaust System Installation
1. Place a clamp over the expanded end of the front muffler assembly and set it into position as shown in figure 4 making sure to install the hangers into the rubber isolators. Do Not tighten the clamp.
2. Place a clamp over the expanded end of the rear muffler assembly and set it into position as shown in figure 5. Do Not tighten the clamps.
3. Check your exhaust system for proper clearance under the vehicle and also for tip alignment.
Read the rest of this entry »

• 0 Comments