how to remove cooling fan on a 2000 audi a4 search result
Hot steam can escape from the expansion tank when the filler cap is opened. Cover the filler cap with a cloth and unscrew it carefully. Note: When the engine is hot the cooling system is under pressure. Carefully open filler cap on expansion tank to release pressure before starting repair work. Hoses are secured with spring-type clips. When repairing only use spring-type clips. VAG 1921 pliers are recommended when installing spring-type clips. The O-rings installed at the quick-release connections must be replaced if damaged or leaking. When installing coolant hoses, make sure that they are free of stress and do not come into contact with other components (observe markings on coolant connection and hose). Perform leak test on cooling system with cooling system tester VAG 1274 and adapter VAG 1274/8.
Cooling system components (on body), removing and installing
Read the rest of this entry »
This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »
Preparing Vertical Side Panels for the Panzer Plate
1. First, on level ground, raise the front of the car evenly. To do this, you may choose to drive the car onto ramps, jack the car up and secure with two jack stands or use a car lift. If using jack stands or ramps be sure to chock the rear wheels and place the car in gear and firmly apply the handbrake. You should also wear safety goggles during this entire procedure.
2. Once the car is safely raised, remove the Original Equipment Audi plastic belly pan if your car still has one. Next, on the driver side, remove the rear T25 Torx screw from the tail end of the plastic vertical engine bay side panel. In order for the Panzer skid plate to fit, the mounting spot on the subframe where the side panel attaches must not have a Torx screw or side panel attached to it. Retain the T25 Torx screws for the final skid plate install.
Read the rest of this entry »
Before beginning repairs on the electrical system: Obtain the anti-theft radio security code. Switch the ignition off. Disconnect the battery Ground (GND) strap. On vehicles equipped with Audi Telematics by OnStar , switch-off the emergency (back-up) battery for the Telematic/Telephone Control Module prior to disconnecting vehicle battery Repair Manual, Communication, Repair Group 01 .
Read the rest of this entry »
OIL PAN – A4 Removal & Installation
1.To bring lock carrier into service position, see LOCK CARRIER .
2. Raise and support vehicle. Drain engine oil into suitable container.
3. Remove noise insulation panel from under engine.
4. For oil pan removal and installation procedures, refer to Fig. 84 -Fig. 93 .
Read the rest of this entry »
Obtain radio code before disconnecting battery. For help in identifying components and component locations:
Removal (Lower Pan- A4 & A6)
1. Disconnect negative battery cable.
2. Remove engine noise insulator (undercover). See Fig. 12 . Drain engine oil.
3. Unbolt left and right swaybar stabilizer bracket bolts (4) from mounting bracket. See Fig. 98 . Lower swaybar stabilizer not more than 10cm (3.94 INCHES) and secure with heavy wire.
4. If vehicle is equipped with automatic transmission, unbolt oil cooler pipe (line) bracket from right side oil pan.
Read the rest of this entry »
The AWE Tuning RSK04 Fueling Kit picks up where the Audi RS4 leaves off! AWE Tuning worked very closely with GIAC to establish the proper mechanical parameters which would overcome limitations in the RS4 that GIAC documented during chip development. The RS4 Mass Air Flow (MAF) sensor and fuel injectors are inappropriate for use on an S4, and we also had our sights set even higher than chipped RS4 territory with the RSK04 kit.
Read the rest of this entry »
The new Audi A6 – the most progressive vehicle takes the lead Design and performance are the main driving elements on its way to the top position. Furthermore, the new Audi A6 embodies the consequent continuation of the familiar Audi brand values, sports appeal, progressiveness and intrinsic quality, which are evident in the fourth generation of this sporty business limousine.
Read the rest of this entry »
Tests/Procedures: 1. Question the customer. Check if he/she started the car, cranked the heater fan on full and went back inside as the car warmed up on a sub-zero morning. Engine temperature rise did not occur at the rate the Powertrain Control Module (PCM) expected. 2. Coolant concentrations of greater than 50/50 can cause this code. Tech Tips: This code will set if the heater system is pulling too much heat from the engine as it is warming up. Engine temperature rise did notoccur at the rate the PCM expected. 2 – Engine Coolant Temperature (ECT) Sensor Confirmed Fix 1 – Coolant Protection 1 – Engine Coolant Level, Engine Coolant Temperature (ECT) Sensor.
Read the rest of this entry »
Covers Audi A4 models builtontheAudi “B5″ platform. Doesnot include AudiS4(sports model). This manual has been prepared using selected factory service information with the added benefit of suggestions tips and clarification of various procedures. Bentley repair manuals provide clear andcomprehensive service and repair procedures.
Read the rest of this entry »
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease