Installation Instructions. Read Me! Rv. 01/04
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake system.
3. Remove (3) nuts & studs from the throttle body & manifold. (Ref. “C”)
4. Remove support bracket from engine block to throttle body. (Ref. “D”)
* Please Note: When removing support bracket bolt at engine block, loosen bolt enough to remove bracket. DO NOT REMOVE BOLT.
Read the rest of this entry »

• 0 Comments

If the complete throttle valve control module is current-less (e.g. connector disconnected) the throttle valve moves into a particular, specified mechanical position, which signals an increased idle speed with an engine at operating temperature. If only the Throttle Position (TP) actuator -V60- is current-less, the throttle valve also moves into the specified mechanical position (emergency running gap), however, since Closed Throttle Position (CTP) switch -F60- can still be recognized, an “almost normal” is reached via the respective ignition angle retardation. If the Engine Control Module (ECM) detects a malfunction at Throttle Position (TP) sensor -G69-, Throttle Position (TP) actuator -V60- is switched current-less by the Engine Control Module (ECM) and the throttle valve moves into the specified mechanical position (emergency running gap) again.
Read the rest of this entry »

• 0 Comments

In the fall of 2008, Quality Control Systems Corp. analyzed data from the National Highway Traffic Safety Administration’s Early Warning Reporting system through the first quarter of 2008. Our analysis showed that injuries allegedly related to vehicle speed control failures in the 2007 Lexus ES 350 had risen to first place in our rankings of unusual patterns of claims. In fourth place on the list was the twin vehicle to the Lexus ES 350, the 2007 Toyota Camry. The Camry claims were also related to vehicle speed control. Our analysis was published on October 24, 2008 by the Vehicle Safety Information Resource Center on its web.
Read the rest of this entry »

• 0 Comments

This kit provides the SOLUTION for eliminating cruise control on throttle bodies found in the 02-06 RSX-S and 02-05 Civic Si while:
-Enabling usage of a short OEM throttle cable (Acura 17910-ST7-L01) for swap cleanliness
-Eliminating throttle cable/bracket interferences (with fuel lines, hoods, hoses, etc.)
-Essentially converting a K20A2/A3/Z1 throttle body into a K20A (Type R) throttle body
-Comprised of high quality billet 6061-T6 machined aluminum.
Read the rest of this entry »

• 0 Comments

REMOVAL OF OLD THROTTLE BODY
1. Disconnect the negative (-) battery terminal.
2. The air inlet tube connecting the air cleaner to the throttle body must be removed. Loosen both of the clamps on the air inlet tube and carefully remove it from the vehicle.
3. Disconnect the throttle position sensor and the idle speed control solenoid connectors from the throttle body. Also disconnect the EGR position sensor connector from the EGR valve.
4. Disconnect the EGR vacuum line from the EGR valve. Disconnect the throttle linkage. Loosen the two hose clamps on the throttle body coolant hoses on the EGR spacer. Remove the hoses being aware that some coolant may drain from the hoses.
5. Remove the four nuts that hold the throttle body to the manifold. Slide the stock throttle body and EGR spacer off of the four studs.
Read the rest of this entry »

• 0 Comments

This bracket provides the SOLUTION for installing a K20A (ITR/CTR/Euro R) cable actuated throttle body into a K-Powered EG, EK, DC2, or EF while:
-Enabling usage of a short OEM throttle cable (Acura 17910-ST7-L01) for swap cleanliness
-Eliminating throttle cable/bracket interferences (with fuel lines, hoods, hoses, etc.)
-Comprised of high quality billet 6061-T6 machined aluminum.
Read the rest of this entry »

• 0 Comments

The installation instructions step:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner housing from throttle body.
3. Remove 5/16” bolt (Ref. “C”) & stud (Ref. “D”) from throttle body.
4. Remove (2) 6mm bolts from throttle linkage bracket and save.
5. Move the throttle body forward then remove the gasket and clean the surfaces.
Read the rest of this entry »

• 0 Comments

Installation Instructions Procedures:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air intake assembly.
3. Remove throttle body intake box and save bolts.
4. Remove (3) bolts from throttle body.
5. Remove bolts from throttle linkage bracket and save.
6. Install power plate using (3) 6mm x 60 bolts and (3) 6mm flat washers. (Ref. “A”)
Read the rest of this entry »

• 0 Comments

Installation Procedure for this body spacer:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake assembly.
3. Remove (2) nuts from the throttle body and (2) studs from manifold. (Ref. “C”)
4. Remove gasket and clean surfaces.
Read the rest of this entry »

• 0 Comments

These instructions are based on my experience with removing and cleaning the throttle body and from information obtained from the 2000 Durango Factory Service Manual. They were originally my notes for use when I have to do it again. They are as complete and detailed as I can make them, however they are provided for informational purposes only and you should follow or use them at your own risk! Other year models may be different; other engines ARE different. If something on yours seems different, it may well be! Use your head and be careful.
Read the rest of this entry »

• 0 Comments