Removal Timing Belt(Esteem)
1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor and power steering pump with hoses attached, and secure out of way. Support engine from above or with floor jack under oil pan. Remove air cleaner case with air cleaner outlet hose. 3. From timing belt end of engine, remove engine mount and mounting bracket. Loosen water pump pulley bolts. Remove water pump drive belt and pulley. 4. Remove 5 crankshaft pulley-to-crankshaft bolts. Remove pulley. It is NOT necessary to remove crankshaft center bolt. Remove timing belt cover. See Fig. 1 . 5. Rotate crankshaft clockwise to align timing marks. See Fig. 2 and Fig. 3 . Stamped “E” on camshaft sprocket must point straight up. Loosen timing belt tensioner bolt and stud nut. Move tensioner away from belt, and hand tighten bolt and nut. See Fig. 4 . 6. If reusing old belt, mark belt with an arrow indicating direction of rotation for installation reference. Remove timing belt.
Read the rest of this entry »

• 0 Comments

The Gear Box was designed to fit under the rear seat of your truck or SUV. The Gear Box gives you a place to store loose items and clutter and ultimately help keep your vehicle organized. It’s designed to fit your vehicle with or without your Husky Liners in place and only takes a few minutes to install.
Read the rest of this entry »

• 0 Comments

1. Remove stock timing cover. Rotate engine to top dead center of cylinder #1 so that the timing marks on the original crank and cam sprockets are directly lined up with each other, i.e. the mark on the crank sprocket will be at 12 o’clock (straight up) and the mark on the cam sprocket will be at 6 o’clock (straight down).
2. Remove sprockets and chain.
3. Install desired offset bushing from enclosed set. Set selection provides 0-Gray, 2-Gold, 4-Copper, 6-Silver, 8-Black, Camshaft Degree Options.
Read the rest of this entry »

• 0 Comments

For cars with a THREADED gear knob (early Audi,VW,Seat to approx 2005) follow the instructions from point 2
For cars with a SLOTTED gearknob (approx 2005 on) follow the instructions from point 8
1. If fitting to an Audi TT, first using a T20 screwdriver, undo all 8 of the T20 screws surrounding the gear stick. Other cars with a screw on gearknob, skip to point 2..then lift the ring away to expose the rubber underneath
2. Unscrew the existing gearknob….and remove the rubber gaitor and aluminium spacer (if applicable) from the gear stick.
Read the rest of this entry »

• 0 Comments

This starter offers high torque, through Gear Reduction at a compact lightweight size. Installation of this starter is similar to the original OEM starter. Designed for use on Chevrolet applications with 153 or 168 tooth ring gears (flywheels).
This starter is designed for 12-VOLT systems only!! Use of this starter with higher than 12 VOLTS or long periods of Read the rest of this entry »

• 0 Comments

Disassembly
1. Remove the differential case (4204). For additional information, refer to Differential Case in this section.
2. NOTE: The differential bearings (4221) need not be removed to overhaul the Ford limited slip differential. If bearing removal is required, use the special tool 205-D072 (D97L-4221-A) and special tool 205–D019 (D80L-630–8) for differential case bearings.
NOTE: The anti-lock speed sensor ring cannot be reused once removed. Remove the differential pinion shaft lock bolt and remove the differential pinion shaft (4211). If required, remove the differential ring gear and anti-lock speed sensor ring.
3. Install the special tool in a suitable vise.
Read the rest of this entry »

• 0 Comments

This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »

• 0 Comments

Bentley Publishers is proud to announce the publication of the BMW Z3 Service Manual: 1996-2002. This repair manual super- sedes our 1996 through 1998 BMW Z3 repair manual with four more model years of coverage, and repair information for the M Coupe and M Roadster. With extensive new information as well as revisions throughout, this book is the comprehensive source of service information and technical specifications available for the BMW Z3 Roadster, Z3 Coupe, M Roadster, and M Coupe.
Read the rest of this entry »

• 3 Comments

Toothed Belt Special tools, testers and auxiliary items required Engine support bridge 10-222 A ( guide 10-222 A/21 changing ) Adapter 10-222 A/8 Torque wrench V.A.G 1331 Torque wrench V.A.G 1332 Pin wrench T10020 Changing the Engine Support Bridge 10-222 A . Guide 10-222 A/21 The engine support bridge 10-222 A is needed to support the engine/transmission subassembly. A new bore is required for securing the adapter 10-222 A/8 to the guide 10-222 A/21 . Dimensions in mm. Drill a 12.5 mm diameter hole – arrow – into the guide 10-222 A/21.
Read the rest of this entry »

• 0 Comments

Vehicles application: Chevrolet P-30 & GMC P-3500
The axle has a banjo-type housing with a removeable carrier. The drive pinion is straddle mounted on removeable carrier. There is no adjustment for drive pinion depth or bearing preload. The preload on the differential side bearings is set by adjusting nuts on which the bearing cups rest. The differential has a two-piece case and four differential pinion gears.
Read the rest of this entry »

• 0 Comments