This blower motor has undergone some changes in design so the installation procedures have also changed. The original motor was a two piece motor and the wheel was secured with a set screw. GM changed the design to a one piece unit with a fiberglass heat shield and the wheel is pressed on. On some of the models you may need to remove the front cradle bolts so the engine can be rocked forward. This will help keep the valve cover from interfering with the blower motor replacement. On all models; disconnect the negative battery cable.
Read the rest of this entry »

• 0 Comments

The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.
The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.
In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.
Read the rest of this entry »

• 0 Comments

Disassembly
1. Thoroughly clean and air dry valve bodies. Remove check balls. Remove each valve train.
2. Lay valves, springs and bushings on a clean surface in the order removed. Remove solenoids, sensor, screens, servos and accumulator assemblies.
Cleaning & Inspection
Clean valves, springs and bushings in solvent. NEVER use shop rags to clean valve body components. Inspect valves and bushings for scoring, nicks and scratches. Inspect springs for damaged or distorted coils. Inspect valve body casting for porosity, interconnected oil passages and damaged machined surfaces.
Read the rest of this entry »

• 0 Comments

The 1971-1974 Eldorado is a classic Cadillac that is fast becoming a collectable and appreciat ing automobile. Sadly, even though Cadillac was a trend-setter in introducing wire wheels for their cars, the current Eldorado owner has few choices when it comes to dressing their car up with wire wheels that add to the elegance of the car. Roadster introduced a line of wire wheels that will work on these cars, however, due to the very limited room in the rear wheel wells and close proximity of the fender skirt fastening hardware, the wire wheels require that there be a few changes made to accomodate the wheels. It is our opinion that these changes should be performed by a qualified bodyshop or fabricator so that there is no risk of harming your car. The purpose of these instructions are to demonstrate what modifications will be involved. None of these modifications will spoil or detract from the original appearance of your car. The modifications required are all to areas that cannot be viewed from the outside.
Read the rest of this entry »

• 0 Comments

The installation of the AEM ECU on the 1995-1999 Mitsubishi Eclipse Turbo / Eagle Talon Tsi uses the stock sensors and actuators. The base map is automatically installed in the base calibrations directory in the AEMPro directory on your computer.
Full details of the test vehicle used to generate this map can be found in the files notes section. However, while the base map is a good starting point and may save you considerable time and money, it will not replace the need to tune your specific application. It is not intended to be driven aggressively. Ignoring this can and will damage your engine.
Read the rest of this entry »

• 0 Comments

1 ) Set aside a couple of cups of the portland cement to be used for the final finishing stages of the repair.
2 ) Cut or chisel the length of the crack creating a notch 1” wide and ―” to 1” deep. Examine the edges of the notch – they should not be smooth. Roughen up the edges if necessary so that the repair will bond firmly to the existing floor.
3 ) Wet the notched area thoroughly.
4 ) Mix the portland cement with the terrazzo chips to create a consistency which is not runny nor is it thick like dough. A consistency you can hold in your hand.
Read the rest of this entry »

• 0 Comments

1995 ENGINE PERFORMANCE General Motors Corp. Removal, Overhaul & Installation Cadillac; Concours, DeVille, Seville
* PLEASE READ THIS FIRST * CAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION section before disconnecting battery.
Read the rest of this entry »

• 0 Comments

Section 1: Repair instructions for E36 1. Connect DIS/MoDiC 3 tester to a vehicle and read out SRS module fault code memory. If the above mentioned SRS faults are set in the airbag control module, proceed with the repair. 2. Remove corresponding front seat. For a removal instructions refer to RA 52 10 000 , or RA 52 10 001 (sports seat) which can be found in the Technical Information System (TIS). 3. Disconnect vehicle’s battery. 4. Remove cable securing wire ties (1), unplug the belt tensioner connector (2) from the belt buckle assembly and from the Read the rest of this entry »

• 0 Comments

This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur.
- Most brake incidents fall into the following categories:
Read the rest of this entry »

• 0 Comments

STEP 1. Begin by removing the small black trim ring that surrounds the radio. Insert the hook tool behind the upper right corner of the trim ring and pull toward you to loosen the ring. Once the ring is loose, work the remaining three (3) corners of the trim ring loose. Set the trim ring aside. Turn the ignition to the “ON” position and shift the transmission into low gear. Just above the ashtray door, grasp the top section of the bezel that surrounds the transmission shifter and pull toward you to release two (2) clips. Insert the hook tool behind the right rear corner of the bezel just behind the shifter. Pull upward to release one (1) clip. Perform the same action in the left rear corner releasing one (1) more clip. Grasp the rear of the bezel and continue working loose two (2) clips on the left and right sides of the shifter. Work the bezel up and over the shifter knob and disconnect all wiring. Set the bezel aside.
Read the rest of this entry »

• 0 Comments