Installation:
If the vehicle has a VES (Video Entertainment System), it must be disconnected! This interface is not compatible with REF model radios. They do not have a VES input available.
1. Remove factory radio. Remove factory female 10 pin Satellite cable, if available. Plug the CHYP’s 10 pin SAT plug into the radio. Plug the factory Satel- lite cable that was just removed into the CHYP’s 10 pin connector.
2. Insert the CHYP’s 22 pin main power Plug (T-Harness) in between the factory radio and factory harness.
Read the rest of this entry »

• 0 Comments

The GROM iPod adapter is designed to provide endless hours of listening pleasure through most vehicles factory radios. You will be able to control iPod with the car stereo buttons or steering wheel controls, and iPod will stay charged when connected to the car stereo. To insure that your iPod performs correctly in your car or truck, we recommend that you read this entire manual before attempting install the GROM interface.
Read the rest of this entry »

• 0 Comments

3.0 GM Class 2 Radio, XM Mode
The BAND button will select/deselect the iWire interface. If both a Terk XM Direct tuner and iPod are attached, the devices will be selected alternately. A typical sequence with both attached will be FM1-FM2-AM-iPod-iPod-FM1-FM2-AM-XM1-XM2 etc. When playing an iPod, SEEK UP and SEEK DOWN will track up or track down within a playlist. At the end of the playlist, the track will wrap around to the beginning. When playing XM, the next channel (up or down) will be selected.
Read the rest of this entry »

• 0 Comments

Vehicle preparation:
1. Remove the negative battery cable before installing the cruise control components for safety precautions.
2. Jeep wrangler applications: remove airbag by using (3) trim tool to release metal clips as shown in figure 2. Caution: ensure that battery has been 90 seconds disconnected for more than prior to removal of airbag; failure to heed this warning may result in airbag discharge and may cause serious injury or death.
Read the rest of this entry »

• 0 Comments

The GROM iPod adapter is designed to provide endless hours of listening pleasure through most vehicles factory radio. To insure that your iPod performs correctly in your car or truck, we recommend that you read this entire manual before attempting install the GROM interface.

Proper mounting location
Securely install the interface in a location free from; heat, humidity, moving parts or direct sunlight. Beware of hot-air flow from your vehicle’s climate control system. We recommend securing the interface to a suitable location, free of sharp metal edges, using double sided tape, Velcro or wire ties.
Read the rest of this entry »

• 0 Comments

Kit Contents: 1. DICE Module 2. Audi radio interface cable (vehicle specific cable) 3. Docking Cable
Installation Steps for this kit
1. Pull vehicle into service bay and access trunk area.
2. Disconnect both battery terminals. These cables must be disconnected during installation to insure proper initialization of the DICE module when the DICE when it is connected.
3. Remove radio by inserting the (4) factory keys (not included) into the slots on each corner of the radio.
4. CD changer interface will be on left hand side of radio, it is the smaller left-hand connector on the bottom of the harnesses. Remove all wiring from the radio unit and remove from vehicle.
Read the rest of this entry »

• 0 Comments

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
Read the rest of this entry »

• 0 Comments

Tests/Procedures: 1. Ground the Violet/Yellow wire (disarm circuit) that goes to either front door and the theft alarm module. Have the keys out of the ignition and all doors closed when grounding the wire. This should disarm the theft alarm system and prevent the theft alarm from arming. 2. Check that the interior lights do not stay on due to the wire being grounded. If they do, the illuminated entry relay will need to be removed or another method of disabling the theft alarm will have to be used. 3. Another method if the theft alarm module is faulty would be to disconnect the module and replace the Powertrain Control Module (PCM) with a new one.
Read the rest of this entry »

• 0 Comments

Follow carefully the instructions listed on these pages and use the template provided, do not over tighten bolts. Do not use silicone on any connections, use urethane Ensure that safe work practices are followed when installing your Airflow Snorkel. Protective ear and eye wear should be worn at all times when using power tools.
Read the rest of this entry »

• 0 Comments

2003-2004 (KJ) Jeep® Liberty NOTE: This notification applies only to the above vehicles equipped with Remote Keyless Entry (Sales Code GXM) built from April 1, 2003 through December 12, 2003 (MDH 0401XX through 121200).
The rear flip-up window switch on about 120,000 of the above vehicles may be improperly sealed and could allow water to enter into the switch. This can cause the flip-up window to open unintentionally if it is left unlocked. The rear flip-up window switch must be replaced on all affected vehicles.
Read the rest of this entry »

• 0 Comments