Monster Exhaust System Installation:
1. Disconnect the negative (ground) cable from the battery (if there is more than one battery, disconnect both negative cables). Secure the cable so it cannot accidentally come in contact with the post.
2. Raise the vehicle and support it securely with properly weight-rated safety stands, ramps or a commercial hoist. Take care to balance the vehicle to prevent it from slipping or falling. When using ramps, be sure the wheels are centered squarely on the topsides. Place the transmission in park (automatic), set the parking brake and securely block the wheels that are on the ground.
Read the rest of this entry »

• 0 Comments

Step 1: Position truck on a flat surface and lift vehicle by the frame so that the front wheels are off the ground using a floor jack and jack stands or a (2) two post lift if available and remove the front wheels and tires. Locate the front sway bar and unbolt the lower end link. Do this on both sides of vehicle. Next locate the lower track bar mount on the passenger side of the vehicle and unbolt from axle. (Insert B)
Step 2: Place an index mark on the stock coil and a matching one on the lower coil pocket. This will allow you to replace the coils in the stock location Next locate the upper shock mounts (they are located in the engine compartment) and remove the upper shock hardware. Next remove the 3 nuts from the upper shock mounts. Do this on both sides of vehicle. Now remove the lower shock mounting bolts and remove the shocks by pulling them up through the engine compartment. Do this on both sides of vehicle.
Read the rest of this entry »

• 0 Comments

1. Apply masking tape completely around the factory upper and lower grille to protect the paint (as shown).
2. Open the hood and remove the plastic header panel covers (by lifting straight up) and six (6) of the top plastic push fasteners.
3. Remove the four (4) factory fasteners (#2 Phillips bit or square drive bit) at the top, bottom and on each side of the factory grille.
4. Unclip the top and the bottom of the factory grille from the bumper cover by pushing down on the upper tabs and pulling up on the lower tabs and pull straight out (shown removed in order to show the screw and tab locations).
5. Use a flat blade screwdriver to pry off the factory black plastic grille fin section from the outer chrome frame.
Read the rest of this entry »

• 0 Comments

When any of the memory switches are pushed while the automatic drive positioner is operating When the adjusting switch for the driver s seat is turned on while the automatic drive positioner is operating When the memory switch 1 or 2 is not pushed and held for at least 1 second When the seat has been already moved to the memorized position When no seat position is stored in the memory switch When the automatic transmission selector lever is moved from P Park to any other position When the driver s door remains open more than 45 seconds and the ignition switch is not in the ON position The automatic drive positioner system can be adjusted and canceled For vehicles with navigation system see Vehicle electronic systems in the Display screen heater air conditioner and audio systems section of this manual For vehicles without navigation system see your NISSAN dealer Pre driving checks and adjustments
Read the rest of this entry »

• 0 Comments

PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting at the Passenger/Right side-front of the vehicle, remove the front factory body bolt & washer.(not re-used) (Fig 1), From the list above select the Passenger/Right side front mounting bracket and the spacer Block secure to vehicle with (1) 12mm x 150mm Hex Bolt, (1) 12mm Flat Washer, (1) 12mm Lock Washers (Fig 1A). Snug but do not tighten hardware at this time.
3. Next, select the T Bolt from the list of parts above, and place the T Bolt into the opening on the Passenger/Right side bottom front frame rail (Fig 2 shows T Bolt placed into frame rail.
Read the rest of this entry »

• 0 Comments

Press the CLOCk button to set hours then use the buttons to adjust 02 01 or Press the CLOCk button again to set minutes then use the or buttons to adjust Press the CLOCk button again to exit clock set mode INTERIOR TRUNk LID RELEASE REMOTE kEyLESS ENTRy SySTEM if so equipped LOCk DOORS Press the LOCk button to lock all doors UNLOCk DOORS Press the UNLOCk button once to unlock the driver s door only Press the button again within 5 seconds to unlock all doors RELEASING TRUNk LID This easy to use Quick Reference Guide is intended to help you more fully appreciate some of the unique features and functions of your new vehicle However it is not intended to replace your Owner s Manual
Read the rest of this entry »

• 0 Comments

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2006 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments

Pre-installation Preparation
1. Verify kit contents.
2. Remove protective wrapping from inserts and place on a non-abrasive surface.
3. Remove the brackets and hardware from the box.

Remove Factory Grille & Frame Assembly
1. Open hood.
2. Remove eighteen 8mm nuts and bolts that hold the frame and grille in place.
IMPORTANT: Keep all hardware in a safe location. You will need this to reinstall your grille.
3. After removing the grille shell lay grille face down on a protective work surface such as a blanket.
Read the rest of this entry »

• 0 Comments

Instruction manual for toyota yaris from Blitz Performance. This kit was produced for a standard stock car. In the case where this kit is installed on a vehicle other than stock, we are unable to guarantee its functional efficiency and durability of the product. Please be careful when installing this product, whereas no foreign objects or liquids get into it. The result of foreign materials getting mixed into the products may cause malfunctions in the products. During installation, in case of any uncertainties, it is important to have a factory service manual at hand. Read the rest of this entry »

• 0 Comments

Remove Plugs – Driver’s Side
Counting from the front, locate the third (3rd) and seventh (7th) plugs on the inner sill for a Quad Cab. For a Mega Cab locate the third (3rd) and eighth (8th) plugs. Use a flat screwdriver to pry them out

Assemble Rear Mounting Bracket Assembly – Driver’s Side
Locate the Rear Mounting Brackets and the Mounting Bracket Support Nuts in the parts kit. Use a Medium Hex Bolt to attach a Support Nut to the back of the Rear Mounting Bracket. If you have a Mega Cab, remove the tape and cut as indicated for the Mega Cab Rear Bracket, if necessary.
Read the rest of this entry »

• 0 Comments