Testing and Inspection of fuel system pressure for 1982 Mercedes Benz 380SL (107 Chassis) V8-3839cc 3.8L SOHC (116)
Test Values
Primary pressure – 5.0-5.6 bar (76-82 psi )
Control pressure, warm-up cycle completed – 3.4-3.8 bar (49-55 psi )
Acceleration enrichment with 500 mbar (15 in. Hg. )vacuum applied to lower connection of warm-up compensator with engine warm – 1.4-1.8 bar (20-26 psi )
Control pressure, engine cold according to ambient temperature warm-up compensator. Refer to charts below.
Read the rest of this entry »

• 0 Comments

Instructions:
1. Remove the stock GM 245mm impeller hub by boring a 3.380″/3.385″ diameter hole on center in the stock GM 245mm impeller (see Figure 1).
2. Install the Sonnax CH-90CM-27 impeller hub from the outside. Weld around the OD of the impeller hub, making sure it is centered in the impeller. This weld must be leak-proof (see Figure 2).
3. Once the impeller hub is fitted, fixture the impeller assembly in the lathe. Turn the lip of the impeller so that it is 3.80″ from the end of the impeller hub. Then turn the OD down to 10.150″/10.145″ diameter, .40″ from the end (see Figure 3).
4. Install the adapter ring on the impeller assembly as shown in Figure 4 and weld around the OD of the impeller. This weld must be leak-proof.
Read the rest of this entry »

• 0 Comments

This B&M Precision Sport Shifter has been designed to work on most 2002+ Acura RSX/Honda Integra (including 6- spd Type-S) and 2001+ Honda Civic models equipped with a manual transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Precision Sport Shifter. Installation of the B&M Precision Sport Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »

• 0 Comments

This B&M Precision Sport Shifter has been designed to work on most models listed above equipped with a manual transmission. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts list and tool lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Precision Sport Shifter. Installation of the B&M Precision Sport Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »

• 0 Comments

This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »

• 0 Comments

For the smoothest installation and best performance and reliability from your supercharger, please follow these simple points.
• Changing the spark plugs to 1 range colder is required with this kit. NGK part# PLFR6A-11 gapped to 1.1mm (0.043in.)
• Read all the instructions to familiarize yourself with various parts and operations.
• Layout all parts on a bench and check that all of the parts are accounted for per the Parts List. Some parts on the list are already assembled, torqued and sealed, DO NOT DISASSEMBLE. If any parts are missing or damaged, please call us immediately.
• Gather all required tools before starting installation.
Read the rest of this entry »

• 0 Comments

This suspension kit consists of all parts necessary to make a successful installation onto your Vehicle. All parts have been tested thoroughly. Please make sure you take all necessary safety precautions while fitting the kit.
Note: you should first read these instructions carefully and then take all parts out of the box and pre-assemble them as far as possible before fitting them onto your vehicle.
Read the rest of this entry »

• 0 Comments

Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended Read the rest of this entry »

• 1 Comment

Due to differences in manufacturing, dimensions and inflated measurements, tire and wheel combinations should be test fit prior to installation. Tire and wheel choice is crucial in assuring proper fit, performance, and the safety of your Pro Comp equipped vehicle. For this application, a wheel not to exceed 10” in width with a minimum backspacing of 3.25” must be used. Additionally, a quality tire of radial design, not exceeding 33” tall X 12.5” wide is recommended. Please note that the use of a 33” X 12.5” tire may require fender modification. Violation of these recommendations will not be endorsed as acceptable by Pro Comp Suspension and will void any and all warranties either written or implied.
Read the rest of this entry »

• 0 Comments

General notes before you use your new parts …
1. The new Bugatti door handles you have purchased are an exclusive product of Model Motorcars, Ltd., based entirely on proprietary research of prototypes and exclusive miniature manufacturing technology, and are only available through us. Please beware of imitations and copies.
2. Our Bugatti door handles are designed to be used as a substitute for the Pocher supplied parts, although some work to modify the doors to adapt the handles is required. Therefore, they are only suggested for experienced Pocher builders adept at modify the kits extensively.
Read the rest of this entry »

• 0 Comments