SECTION 501-09: Rear View Mirrors REMOVAL AND INSTALLATION
Aero-Style Mirror NOTE: LH exterior mirror shown, RH exterior mirror similar. 1 14631 Exterior mirror electrical connector 2 W705760 Exterior mirror nut (3 required) 3 17K707 Exterior mirror glass 4 — Dampener springs (part of 17K707) 5 — Exterior mirror motor screw (3 required) (part of 17D696) 6 17D696 Exterior mirror motor 7 — Exterior mirror lower cover screw (3 required) (part of 17682 RH/ 17683 LH) 8 — Exterior mirror lower cover (part of 17682 RH/ 17683 LH) 9 17D742 RH/ 17D743 LH Exterior mirror upper cover 10 17682 RH/ 17683 LH Exterior mirror
Read the rest of this entry »

• 0 Comments

1. Open driver side door. Lower window.
2. Remove door lock cover.
3. Unsnap and remove the triangular molding that covers the mirror mounting screws.
4. Unsnap and remove the molding that covers the door handle. Remove the screw behind the door handle.
5. Unsnap the control console and unplug the wires. Remove the screw located behind the arm rest.
6. Dislodge the door panel by pulling it up and away from the door slightly. Disconnect light and tweeter connections and remove door panel.
7. Secure mirror with one hand. Proceed cautiously to avoid dropping articles into the door panel. Remove the 3 mirror mounting nuts using a 10mm socket.
Read the rest of this entry »

• 0 Comments

1. Open the driver side door and lower the window. 2. Pry open the control panel starting from back as shown. Remove the door panel and disconnect the mirror wire harness. 3. Remove screws: 3 @ bottom (A, B, and C), 2 hidden under caps (D and E), and 1 under control panel (F), and 1 hidden behind door handle (G). A total of 7 screws. Remove ring around door handle. Remove the three mirror mounting nuts and remove the mirror housing from the vehicle.
Read the rest of this entry »

• 0 Comments

Procedures of LED Mirror-Beam installation on Dodge Charger/Magnum.
Removing the Side Mirror:
NOTE: This product can not be used if your vehicle is equipped with break-away mirrors.
1. Remove the driver side door panel from the vehicle (Fig. 1). To remove the door panel: Remove the 5 caps labeled “A” (Fig. 1). Take a pen or other object and depress the center of the cap. This will disengage the cap so it can be removed, then remove the Phillips head screws under the two covers labeled “B”. Remove the 3 clips from inside the window track (Fig. 1). Remove the 4 Phillips head screws from the bottom of the door panel. Unhook the door opener rod and unplug the 3 electrical connectors behind the door panel.
Read the rest of this entry »

• 0 Comments

Starting in 2000 an accessory Auto Dimming Mirror was available. The mirror could come equipped with an electronic compass or an ambient temperature sensor or Homelink (Homelink allows you to program your garage remote to one of three buttons on the mirror assembly). This bulletin describes the mirror operation and diagnosis. NOTE: Mazda6 may come with factory or accessory installed auto-dimming mirror. If the unit is factory installed, look in the wiring diagram for wiring information, if the unit is port or dealer installed, then the wiring information in this bulletin applies.
Read the rest of this entry »

• 1 Comment

STEP 1
Roll both front windows completely down and then disconnect the vehicles battery. Read all instructions before proceeding to STEP 2.
NOTE: If you are installing a manual mirror do not disconnect the battery.
STEP 2
Remove the screw from the sail inner trim panel, using a Phillips head screw driver.
WARNING: Do not try to remove the sail inner trim panel after you remove the screw, as it is still connected to the door trim.This panel will be removed in Step 7.
Read the rest of this entry »

• 0 Comments

Motor vehicle theft is a serious problem in many parts of the world. In the United States, the annual loss from car theft is over $4 billion. The Automotive Information Council reports that over one million motor vehicles are stolen in the U.S. each year. That’s one motor vehicle theft every 31 seconds.
Read the rest of this entry »

• 0 Comments

The polished black cover on each mirror can be removed and painted to match the vehicle’s body color, or replaced with chrome (p/n 9040) or ‘USA Flag’ theme covers (p/n 9060). Find below the removal/installation instructions for the cover.
Existing cover removal.
Make sure you have the required tools:
• flashlight
• slotted screwdriver (with at least a 5” shaft).
Approximate installation time: 5 –10 minutes.
Read the rest of this entry »

• 0 Comments

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory should follow approved guidelines to ensure a quality installation. These guidelines can be found in the “Accessory Installation Practices” document. This document covers such items as:- • Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). • Safety (eye protection, rechecking torque procedure, etc.). • Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). • Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Read the rest of this entry »

• 0 Comments

This blower motor has undergone some changes in design so the installation procedures have also changed. The original motor was a two piece motor and the wheel was secured with a set screw. GM changed the design to a one piece unit with a fiberglass heat shield and the wheel is pressed on. On some of the models you may need to remove the front cradle bolts so the engine can be rocked forward. This will help keep the valve cover from interfering with the blower motor replacement. On all models; disconnect the negative battery cable.
Read the rest of this entry »

• 0 Comments