The GM12LAN-AUX/S converts the XM satellite radio port of the GM radio into an auxiliary input. The GM12LAN-AUX/S provides full compatibility with the factory On-Star system, and factory XM Satellite Radio. Additional harness is required. (Not included).

INSTALLATION:
CAUTION: BEFORE ANY CONNECTIONS ARE MADE, PIE STRONGLY RECOMMENDS THAT ALL CIRCUITS BE VERIFIED WITH A VOLTMETER BEFORE ITERFACING WITH THEM. ALWAYS SET THE PARKING BRAKE BEFORE WORKING ON ANY VEHICLE.
DO NOT force connectors together as pin damage may occur. This installation will be flawless if you take your time making the connections described below. Following the installation sequence below is critical to ensure proper recognition of the auxiliary interface by the factory radio.
Read the rest of this entry »

• 0 Comments

Thank you and congratulations on the purchase of a Pacbrake replacement Dodge elbow to increase ex- haust flow. Read the entire installation manual carefully to ensure you can complete the installation once started. Check that your Pacbrake kit is correct for the application and contains all the necessary parts as shown in the photo.

INSTALLATION INSTRUCTIONS:
1. Exhaust Elbow Installation: All vehicles, remove the two capscrews that attaches the cast elbow to the header pipe. 1994-1998 vehicles, remove the V clamp between the elbow and the turbo charger. Remove the cast elbow. Removal of the 5 bolt flange is required. 5 new fasteners will be supplied. 1999-2002 vehicles, remove the 5 capscrews securing the elbow to the turbo charger. Remove the cast elbow, 5 new fasteners will be supplied.
Read the rest of this entry »

• 0 Comments

Explorer delivers versatility and rugged capabilities with the guts to meet the hectic demands of your lifestyle. With towing of up to 7,115 pounds, the choice of a spirited 292 hp 4.6L V8 engine and seating for up to seven passengers, Explorer is designed to deliver.
KEY FEATURES
• Standard 210 hp 4.0L SOHC V6 engine with 5-speed automatic transmission
• Optional 292 hp 4.6L 3-valve V8 engine with 6-speed automatic transmission
• Tows trailers up to 7,115 lbs. when properly equipped (4.6L V8/4×4)
• Independent rear suspension tackles rough terrain and uneven road surfaces with ease
Read the rest of this entry »

• 0 Comments

This document covers the installation of RECON Truck Accessories 3-Piece running lights on a 2003 Chevrolet/GMC Silverado/Sierra 2500 HD.
The installation takes approximately 2 to 3 hours and can be broken down into 5 main steps:
Read the rest of this entry »

• 0 Comments

The Crane HI-6DI2 part number 6000-6500 is a CD ignition with two independent coil outputs. The unit is intended for distributorless applications such as the Diamond Star Motors (DSM) Mitsubishi engine used in Eclipse, Eagle Talon and Plymouth Laser as well as most other four cylinder distributorless engine applications with two coils. Two HI-6DI2 units can be used for Ford 4.6L V8 distributorless engine applications. The HI-6DI2 is 50 states legal for 1995 and prior years distributorless vehicles without OBD II on board diagnostics (CARB E.O. D-225-57).
Read the rest of this entry »

• 0 Comments

Features of the ATS Valve Body:
Increased transmission lubrication, even in park.
Increased transmission torque capacity.
Lock up capability in all gears, including manual 1st and 2nd gears.
Downshift from 4th to 3rd while maintaining applied lock-up clutch.
Reduce torque converter drain back after sitting for long periods of time.
Read the rest of this entry »

• 0 Comments

Refer to Wiring Diagrams Cell 55, Electronic Automatic Temperature Control (EATC) for schematic and connector information.
1. Verify the customer’s concern by operating the climate control system to duplicate the condition.
2. Inspect to determine if one of the following mechanical or electrical concerns apply:
Visual Inspection Chart
Read the rest of this entry »

• 0 Comments

EGO TS is the intelligent entry-level solution for telephone use in your car: simple to operate, elegant and compact – with Bluetooth and audio enjoyment too. The installation of your EGO TS in your car requires specialist knowledge and skills. We recommend that the installation be carried out in a qualified professional workshop. Before installation in your car, please make sure that your mobile phone is fully compatible with EGO TS. If you are uncertain, please consult your dealer or a professional workshop. Our service team will also be happy to help you with any information you may require. You can find further information on compatibility between EGO TS and various mobile phones on our website.
Read the rest of this entry »

• 0 Comments

Tools & Procedures
• EQUIPMENT: Damper Installation Tool
• Anti-seize Compound
• The Proper Key
• Whenever it’s necessary to remove a vibration damper, only a proper puller tool should be used.
• DO NOT use a hammer during installation.
• Honing or machining Fluidampr bore is not recommended. A diametrical press fit of .0005″ to .0015″ is recommended for proper damper function. (Aluminum Fluidampr p/n’s 630102, 630112, 630602, 660202, 720102, 720112, 740102, 730602 & 740112 require a diametrical press fit of .001″ to .0025″.) If a micrometer is available, you may want to measure the crank snout and the inner bore of Fluidampr to assure proper fit.
Read the rest of this entry »

• 0 Comments

Installation procedure will be separated into the following categories:
1. Special EFI parts required.
2. Removal of non-required parts from carbureted engine.
3. Installation of TBI and engine hardware.
Read the rest of this entry »

• 0 Comments