Information on Upgrading Certain OnStar® Generation 5 Analog/Digital-Ready Systems to OnStar® Generation 6 Dual-Mode (Analog/Digital) This bulletin is being issued to provide dealer personnel with information and procedures to follow should an owner wish to upgrade their OnStar® Generation 5 analog/digital-ready system to an OnStar® Generation 6 Dual-mode (analog/digital) system.
Service Procedure
Read the rest of this entry »

• 0 Comments

After installation, the ONSTAR LOCKPICK will allow your aftermarket Bluetooth Handsfree kit to interface directly with your vehicle’s ONSTAR system. When you are making or receiving a call, your ONSTAR will be activated and the audio can be heard through your factory sound system. The ONSTAR LOCKPICK contains a simple “T” harness for connection to your radio. This “T” harness also has connections for your Handsfree kit to supply power for it, and connect to its radio mute function. A separate harness allows connections to the line level audio output of your Handsfree kit so you will not have to use any of the extra speakers which may have come with your kit. You can listen to your conversations just as you would an ONSTAR message and the sound will play through your factory sound system.
Read the rest of this entry »

• 0 Comments

RAM Street Dual disc systems are specifically engineered for today’s late model performance cars and engine swaps into earlier vehicles. The purpose of these clutches is to provide smooth driveability for high power levels that was previously not available using aggressive friction material single disc clutches. Friction material is not the only consideration for good driveability. We also need to maintain enough overall weight in the clutch assembly so that the clutch can be driven at Read the rest of this entry »

• 0 Comments

Read all instructions before starting any work.
1. Remove the O.E. muffler and tail pipes only. Any pipe ahead of the OE muffler should be retained. Lubricate the rubber isolators and fasteners with WD-40, or similar product, to aid in removal.
2. Place a 3″ band clamp on the inlet of DynoMax front pipe 51061 and install. Slightly tighten the inlet band clamp.
3. Install DynoMax Ultra Flo SS muffler 17273. Place a 3″ saddle clamp on the muffler inlet connection and finger tighten. Rotate the muffler to a 450 angle with the top toward the drive shaft. Please see system diagram.
Read the rest of this entry »

• 0 Comments

Installation Procedure:
Step 1: Disconnect ground cables from both batteries. Inspect all parts and make sure they are free from defect and debris. Using compressed air, clean new parts.
Note: Clean exterior of pump and rail before attempting to install the Dual Feed Line. The smallest amount of dirt or debris can fail the Bosch high pressure fuel system.
Step 2: Remove air inlet horn from engine.
Step 3: If applicable, remove TPS/Throttle positioning housing bolts (Three 13mm bolts) and move the TPS/Throttle positioning housing out of the way.
Read the rest of this entry »

• 0 Comments

RGB Module Connections & Controls
The NV_RGB_X Video Interface is capable of both single video and dual video modes of operation. For dual video mode, the optional remote control pad is recommended for switching between the video inputs on the module.
Installation With Plug And Play Factory Harness
Read the rest of this entry »

• 0 Comments

Dual Fueler CP3 Pump Kit Installation Guide 03-07 5.9 Dodge Cummins
Engine noisy – Too Much Fuel Pressure or fuel delivery code
1) Cause: Check fuse is good and in controller’s fuse holder securely, and all power connections are secure, including connectors for both pumps are fully plugged in.
2) Lift pump pressure supplying both CP3 pumps pressure too high. Supply pressure from lift pump should not exceed 12-15 psi.
Read the rest of this entry »

• 0 Comments

Banks Monster® Exhaust System Dual-Tip 2007-2008 Dodge 6.7L Cummins ISB Pickup Trucks Including Mega Cab Owners Manual.
1. For ease of installation of your Banks system, familiarize yourself with the procedure by reading the entire manual before starting work.
2. The general assembly diagram (Figure 1) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction.
Read the rest of this entry »

• 0 Comments

This kit was designed for use with TM Kit# F4531. Use of this kit with other suspension kits and shocks, including coilovers, has not been verified. Proceed with caution. Interferences may exist. This kit should only be installed on a vehicle that is in good working condition. Before you install the kit, thoroughly inspect the vehicle for corrosion or deformation of the sheet metal. If the vehicle is suspected to have been in a collision or misused, do not install this kit. Off-road use of your vehicle with this kit installed may increase the stress applied to the factory components. Failure to observe this warning may result in serious personal injury and/or severe damage to your vehicle.
Read the rest of this entry »

• 0 Comments

This manual contains the pre-installation, assembly and installation for dual player headrest video on Toyota Prius 2010.
Pre-installation Precaution
1. Use Seat and Floor Protectors to avoid damage to surfaces.
2. If the vehicle is equipped with an Anti-theft radio, the radio code must be written down prior to disconnecting the battery cable. The code must be re-entered when the negative battery cable is reinstalled. Disconnecting the battery
Figure may cause certain vehicle settings to be lost. Manufacture’s recommendations for the battery B3 removal should be followed. Disconnecting the battery is recommended.
Read the rest of this entry »

• 0 Comments