2003-2004 (KJ) Jeep® Liberty NOTE: This notification applies only to the above vehicles equipped with Remote Keyless Entry (Sales Code GXM) built from April 1, 2003 through December 12, 2003 (MDH 0401XX through 121200).
The rear flip-up window switch on about 120,000 of the above vehicles may be improperly sealed and could allow water to enter into the switch. This can cause the flip-up window to open unintentionally if it is left unlocked. The rear flip-up window switch must be replaced on all affected vehicles.
Read the rest of this entry »

• 0 Comments

Vehicle preparation:
1. Remove the negative battery cable before installing the cruise control components for safety precautions.
2. Jeep wrangler applications: remove airbag by using (3) trim tool to release metal clips as shown in figure 2. Caution: ensure that battery has been 90 seconds disconnected for more than prior to removal of airbag; failure to heed this warning may result in airbag discharge and may cause serious injury or death.
Read the rest of this entry »

• 0 Comments

WIRING OVERVIEW
Switch Settings (read below for explanation)
Selecting The Vehicle Type
Switches 1,2, and 3 are used to select vehicle type. Use the chart on the back of these instructions to determine which of the above switch settings you will need.
Read the rest of this entry »

• 0 Comments

Installation Procedure below:
Front Installation:
1. Secure & properly block the tires of the vehicle on a level concrete or asphalt surface.
2. Raise the front of the vehicle in accordance to the manufactures recommendation & support with jack stands.
3. Remove the front tires / wheels.
4. Remove the upper ball joint nut & separate the upper ball joint from the steering knuckle using a ball joint remover or other suitable tool.
5. Disconnect the lower strut fork at the lower control arm & the lower portion of the strut assembly.(See Photo #1)
6. Remove the air box on the passenger side.
7. Remove the 4 upper strut nuts on the strut tower that holds the strut assembly to the strut tower.
8. Separate the strut fork from the strut assembly & remove the strut from the vehicle.
Read the rest of this entry »

• 0 Comments

This bulletin is being revised to add the 2005 model year and update the part number information for Permatex Quick Grid. Please discard Corporate Bulletin Number 03-08-44-005B (Section 08 — Body and Accessories).
Condition
Some customers may comment that the radio has poor reception or radio static/increased interference when the rear window defogger is turned on. Also, some rear window defogger grids may be inoperative.
Read the rest of this entry »

• 0 Comments

Due to the rapid and forceful deploy of airbags, aftermarket equipment that is mounted in airbag deployment zones can quickly become projectile objects, in the event of an impact. A Pro-gard AOI Airbag On/off Switch can provide safety and peace of mind for vehicle operators against such situations.
Read the rest of this entry »

• 0 Comments

2003 – 2005 model year Matrix vehicles produced BEFORE or AFTER the VIN shown below. Part numbers vary based on Matrix vehicles produced before or after the VIN (refer to the Parts Information table in this TSB). Front Doors Repair Procedure Refer to steps 1 – 6 in the Technical Information System (TIS): 2003, 2004, or 2005 model year Matrix Repair Manual: Engine Hood/Door: Front Door: Overhaul.
Read the rest of this entry »

• 0 Comments

The mounting procedure outlined below covers the 1997-2002 Jeep Wrangler. Note that a
Front Gross Axle Rating (FGAWR) of 2500 lbs. is required. A suspension upgrade and additional
ballast may be necessary. You will need to refer to the illustrations and familiarize yourself with each
of the undercarriage components and their relative position to each other. Then proceed as follows:
Begin by removing the four screws that hold the plastic “Jeep” valance in place above the
bumper. Keep these screws as they will need to be reinstalled.
Read the rest of this entry »

• 0 Comments

1. Unplug all lights and harnesses connected to factory bumper and remove from truck frame.
2. Remove factory tow frame to install new Top Gun rear bumper. In order to remove tow frame, the bed of the truck has to be loosened on lifted 6 inches off the truck frame. Remove 4 bolts towards the rear of the bed, end loosen but do not remove the 2 bolts towards the front of the bed. Lift bed and remove towing frame.
Read the rest of this entry »

• 0 Comments

Kit parts are prefaced by the word kit and appear in bold print. 1. Carefully read all warnings and instructions completely before beginning.
2. Verify all parts have been received in this kit by checking the parts list at the end of this document.
3. Only install this kit on the vehicle for which it is specified. If anytime during the installation you encounter something different from what is outlined in the instructions, call technical support at (928) 636-3175.
4. Park vehicle on a clean, dry, flat, level surface and block tires so vehicle cannot roll in either direction. Adhere to recommendations when replacement fasteners, retainers and keepers are called out in the factory service manual. When re-assembling the vehicle it is recommended Read the rest of this entry »

• 1 Comment