These instructions are based on my experience with removing and cleaning the throttle body and from information obtained from the 2000 Durango Factory Service Manual. They were originally my notes for use when I have to do it again. They are as complete and detailed as I can make them, however they are provided for informational purposes only and you should follow or use them at your own risk! Other year models may be different; other engines ARE different. If something on yours seems different, it may well be! Use your head and be careful.
Read the rest of this entry »

• 0 Comments

This undercarriage fits all models listed but the cross member connection will vary. Refer to step “a” for the 1987–96 Dodge Dakota, 1997–03 Dodge Dakota Sport, 1997–03 Dodge Dakota SLT Extended Cab and 1998–03 Dodge Durango SLT models. Refer to step “b” for the 1997–04 Dodge Dakota and 1998–03 Dodge Durango.
Read the rest of this entry »

• 0 Comments

1. For the Dakota: Remove bumper, retaining all OEM fasteners for reinstallation.
Proceed to Step 2.
For the Durango: Prior to removing the bumper, cut and remove the center portion of the bumper and air dam as shown in the photo below. Retain the cut out section of the air dam to fabricate an air deflector in Step 8. Remove the remaining bumper assembly, retaining all OEM fasteners for reinstallation.
2. Clamp the driver-side mount plate to the outside of the driver-side vehicle frame. Make sure the mount alignment tab fits up against the back of the vehicle frame front plate, and the front and rear plate stiffeners are snug against the bottom of the frame. When positioned correctly, mount plate holes align near the center of the vehicle frame.
Read the rest of this entry »

• 0 Comments

This manual is intended for the installation of the Powerdyne Supercharger kit, Part Number K10513 on the Dodge 318 or 360 C.I. motors, model years 1999–2000 This kit is designed to be 50 state smog legal and as of the writing of this manual C.A.R.B. (California Air Resources Board) exemption is pending. This kit already complies with Federal EPA memorandum 1A, making it smog legal in 49 states, providing your states pollution laws do not supercede EPA memorandum 1A.
Read the rest of this entry »

• 0 Comments

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
TOOLS REQUIRED: #2 Phillips screwdriver, 5/64” drill bit, drill, marking pen.
PARTS INCLUDED: Pro.Fit VSMTM, instructions, two (2) #10×5/8” screws.
LOCATION: Lower right corner of radio, below the radio.
Read the rest of this entry »

• 0 Comments

Included with your Poweraid Spacer is a sticker with a California Air Resources Board (C.A.R.B.) Executive Order (EO) number. This sticker must be placed in plain view inside of the engine compartment. Failure to do so may prevent you from passing a smog inspection.
Installation Procedure:
1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove air cleaner assembly.
3. Using 1/2” socket, remove (4) 5/16” bolts attaching throttle body to manifold.
4. Lift throttle body.
Read the rest of this entry »

• 0 Comments

WHEN INSTALLING THIS EXHAUST SYSTEM MAKE SURE TO USE PROPER SAFETY PRECAUTIONS. USE JACK STANDS WHEN UNDER TRUCK, SET PARKING BRAKE, BLOCK TIRES AND USE SAFETY GLASSES AND GLOVES. DO NOT WORK WITH HOT PIPES!
SUGGESTED TOOLS:
9/16” SOCKET & WRENCH, 15MM SOCKET, ―’ SOCKET & WRENCH, HACKSAW, JACKSTAND,WD-40

DO NOT REMOVE THE STOCK HEADPIPE.CUT 1 ―” IN FRONT OF STOCK MUFFLER. FOR AN EASIER REMOVAL OF THE STOCK EXHAUST CUT THE FACTORY TAILPIPE BEHIND THE MUFFLER. LEAVE ALL FACTORY RUBBER GROMMETS IN PLACE. SPRAY WD-40 ON ALL RUBBER STOCK HANGERS FOR EASIER REMOVAL.
Read the rest of this entry »

• 0 Comments

This undercarriage fits all models listed but the crossmember connection will vary. Refer to step “a” for the 1987-1996 Dodge Dakota, 1997-2003 Dodge Dakota Sport, 1997-2003 Dodge Dakota SLT Extended Cab and 1998-2003 Dodge Durango SLT models. Refer to step “b” for the 1997-2004 Dodge Dakota and 1998-2003 Dodge Durango
1. Disconnect the fog lamp harnesses if applicable, and then remove the bumper.
a. Remove the bumper mount plates from in between the frame rail and radiator. Discard the mount plate hardware.
b. Permanently remove the air dam from the truck frame crossmember. Remove the fasteners that are pressed into the bumper bracket on the frame rail. Secure the bracket and frame wall with vise grips and then use a hammer to punch out the fasteners.
Read the rest of this entry »

• 0 Comments