This bulletin is being revised to add the 2005 model year and update the part number information for Permatex Quick Grid. Please discard Corporate Bulletin Number 03-08-44-005B (Section 08 — Body and Accessories).
Condition
Some customers may comment that the radio has poor reception or radio static/increased interference when the rear window defogger is turned on. Also, some rear window defogger grids may be inoperative.
Read the rest of this entry »

• 0 Comments

Dash Disassembly:
1. Disconnect the negative battery terminal to prevent an accidental short circuit.
2. Unclip the trim panel surrounding the climate controls and radio including the hazard switch panel. Unplug and remove the panel. (Figure A)
3. Unclip and remove pocket if so equipped. (Figure B)
4. Remove (4) T-20 Torx screws securing the radio. Unplug and remove radio.
Read the rest of this entry »

• 0 Comments

Installation Note: This vehicle is designed with 2 different radio styles. Each radio design requires a completely different method of installation for a new replacement radio. The most important thing to understand is the difference between the plastic dash panel that surrounds the 2 different radio styles. This plastic dash panel actually dictates how you install your new replacement radio. Read below to find out why.
Read the rest of this entry »

• 0 Comments

Subject: Radio With Six Disc CD Changer Does Not Recognize Loaded CD And Displays An “INITIALIZING” Message, CD Will Not Play, CD Cannot Be Ejected, Or Disc Icon Does Not Illuminate (Reprogram Radio)
Models:
2005-2006 Chevrolet Avalanche, Suburban, Tahoe
2005-2007 Chevrolet Colorado, Express, Silverado Classic, TrailBlazer
2005-2006 GMC Yukon, Yukon XL
2005-2007 GMC Canyon, Envoy, Savana, Sierra Classic
2005-2006 HUMMER H2 with Six Disc CD Changer Equipped Audio System (RPO UC6)
Read the rest of this entry »

• 0 Comments

If your original radio had a braided strap bolted to the rear of the radio.
TIP: Crimp a ring terminal to the new radios ground wire and insert a bolt through both connectors to connect the ring terminal of the braided ground wire to the ring terminal attached to the new radios ground wire.
If your original radio had a plastic connector containing a single wire plugged into the rear of the radio.
TIP: Crimp a male tab spade to the new radios ground wire. Slide it into the female tab spade connector that had originally snapped into the rear of the factory radio.
Read the rest of this entry »

• 0 Comments

STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in the shape as shown in the photos above. For more information on how to remove the radio, see the diagram below.
STEP 2: Pull the radio from the dash. Unplug the antenna cable from the rear of the radio. Unplug the 2 wire harness connectors from the rear of the radio.
Read the rest of this entry »

• 0 Comments

Remove Factory Radio
STEP 1: Locate and remove two (2) phillips screws that secure the top of the plastic panel that covers the radio and air conditioner controls. They should be located next to the air conditioner vent levers directly above the (2) air conditioner vents. Pull the plastic panel gently from the top to remove it from the dash.
STEP 2: The radio will be held in with two (2) 7mm bolt screws; one on each side of the radio. Remove both.
STEP 3: To remove the radio, pull firmly. Unplug all connectors (1 blue, 1 white, 1 black) from the rear of the radio. Unplug the antenna cable from the rear of the radio. The radio is now free to be removed from the dash panel.
STEP 4: Since the opening is so big in the dash, The Install Doctor recommends using the plastic mounting bracket attached to the bottom of the radio just removed.
This bracket can then be attached to the bottom of the plastic radio installation kit and assure that this kit is properly aligned and secured to the dash.
Read the rest of this entry »

• 0 Comments

The OS-2CTS is a plug and play interface that allow the installation of an aftermarket radio into Cadillac CTS and SRX vehicles. It will maintain operation of the On Starо and factory amplified audio system. On Starо audio will play through the front speakers when active. It also retains all warning chimes and Vehicle Rear Parking Assist chimes.
• Class II circuitry will not disable vehicle data bus even if interface loses power.
• On Starо active LED and Ignition on LED.
• Provides +12v switched accessory output. No more searching for switched +12v in fuse box or kick panel.
• Mute output to either mute the aftermarket radio or to turn if off when On Starо is active.
• On Starо Volume control via factory steering wheel audio controls or click wheel .
• New radio will operate with the vehicle RAP (Retained Accessory Power) system, which is 10 minutes or until a door is opened.
Read the rest of this entry »

• 0 Comments

Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although the instructions in this guide explain how to install the Terk TRK-SR2 Roof-Mount Satellite Radio Antenna in a general sense, they do not show the exact installation methods for your particular vehicle. IMPORTANT: If you are not comfortable performing a complex installation, ask your local mobile audio dealer about professional installation options.
Read the rest of this entry »

• 0 Comments

This Owner’s Manual is designed to serve as your comprehensive guide to the wide range of functions and features provided by your BMW Radio and Information System. Thorough familiarity with this manual’s contents will assist you in becoming acquainted with the system’s extended array of special technical features. This Owner’s Manual contains descriptions of the following systems: BMW Car radio Onboard computer DSP – Digital Sound Processing* Cellular phone* You will find a summary of standard radio functions and operating instructions on pages 5 and 6. The control options for using the Multi-Information Display (MID) are listed on pages 3 and 4.
Read the rest of this entry »

• 0 Comments