Installation: 2005 Dodge Charger or Magnum
1. Remove the 2 plastic covers that protect the front area under the hood (Fig. 1). They snap into or out of the vehicle.
2. Remove the 2 bolts that hold the hood latch assembly on and set it aside (do not disconnect the cables). Unplug the horn wire and place the wire out of the way (Figs. 1 & 2).
3. Mount speaker to bracket (Fig. 3).
4. Remove all the plastic rivets from the top of the front of the body of the vehicle, then pull the body toward the front of the vehicle (the body is flexible). Slide the 2 U-Nuts onto the support braces (Fig. 4) and place the bracket (with siren attached) on top of the U-Nuts. The front “ears” of the bracket rest on the two U-Nuts which clip onto the support braces (Fig. 4). The rear of the bracket will mount behind the hood latch assembly using the hood latch’s mounting hardware (Fig. 2).
Read the rest of this entry »

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
Read the rest of this entry »

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
Read the rest of this entry »

• 0 Comments

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2008 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments

Speaker installation requires drilling two 13/32″ holes in the passenger side frame forward of the front wheel. To install the speaker, proceed as follows:
1. Locate the frame on the vehicle’s passenger side forward of the front wheel well. Before drilling or cutting holes in ANY part of a vehicle, be sure that both sides of the mounting surface are clear of parts that could be damaged; such as brake lines, electrical wiring or other vital parts.
Read the rest of this entry »

• 0 Comments

Procedures of LED Mirror-Beam installation on Dodge Charger/Magnum.
Removing the Side Mirror:
NOTE: This product can not be used if your vehicle is equipped with break-away mirrors.
1. Remove the driver side door panel from the vehicle (Fig. 1). To remove the door panel: Remove the 5 caps labeled “A” (Fig. 1). Take a pen or other object and depress the center of the cap. This will disengage the cap so it can be removed, then remove the Phillips head screws under the two covers labeled “B”. Remove the 3 clips from inside the window track (Fig. 1). Remove the 4 Phillips head screws from the bottom of the door panel. Unhook the door opener rod and unplug the 3 electrical connectors behind the door panel.
Read the rest of this entry »

• 0 Comments

Read all instructions before starting any work.
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂” clamps that connect the mufflers to the x-pipe.
Read the rest of this entry »

• 0 Comments

Neon Front Door Instructions:
1. Using a pick tool pry open the screw cover behind the interior door release lever and remove the screw.
2. Remove the screws in the armrest pocket and at the top of the door near the front.
3. For models with manual windows use a window crank removal tool to disengage the pin securing the window
crank and pull the window crank from the door. The triangle shaped piece that houses the side mirror
adjustment control lever will need to be pulled away from the door. Using a panel removal tool gently pry
the bottom of the plastic away from the door to release the fasteners and let it hang by the mirror control cables.
Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2004 Cadillac SRX WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE 12V wires at the ignition harness are low current 12V sources that should not be used to drive any high current positive circuits. Must go to the battery for 12V. LT.GREEN Ignition Harness POWER DOOR LOCK (-) RED/BLACK At Door Lock Switch Inside Driver Door POWER DOOR UNLOCK (-) ORANGE/BLACK At Door Lock Switch Inside Driver Door PARKING LIGHTS (+) DO NOT USE PARKING LIGHTS (-) BROWN/WHITE In Brown Plug At Module Under Glove Box LEFT FRONT DOOR TRIGGER (-) TAN At Driver Door Module In Driver Door RIGHT FRONT DOOR TRIGGER (-) LT.GREEN At Module Inside Right Read the rest of this entry »

• 1 Comment

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2006 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments