Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the arm rest and remove the screws.
2. Remove the four screws securing the door panel along the bottom.
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers securing the door panel. The center pin of the plastic retainer should depress approximately 1/8” and allow the retainer to be removed from the door panel. The two uppermost retainers do not need to be removed in order to remove the door panel.
Read the rest of this entry »

• 0 Comments

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2006 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments

Procedures of LED Mirror-Beam installation on Dodge Charger/Magnum.
Removing the Side Mirror:
NOTE: This product can not be used if your vehicle is equipped with break-away mirrors.
1. Remove the driver side door panel from the vehicle (Fig. 1). To remove the door panel: Remove the 5 caps labeled “A” (Fig. 1). Take a pen or other object and depress the center of the cap. This will disengage the cap so it can be removed, then remove the Phillips head screws under the two covers labeled “B”. Remove the 3 clips from inside the window track (Fig. 1). Remove the 4 Phillips head screws from the bottom of the door panel. Unhook the door opener rod and unplug the 3 electrical connectors behind the door panel.
Read the rest of this entry »

• 0 Comments

Front Door Installation for Magnum, Charger, 300C
1. Using a pick tool pry open the screw covers behind the interior door release lever and below the
arm rest and remove the screws. Fig. 1
2. Remove the four screws securing the door panel along the bottom. Fig. 1
3. Using the end of a Phillips screwdriver gently depress the center pin of the three plastic retainers
securing the door panel. The center pin of the plastic retainer should depress approximately 1/8”
and allow the retainer to be removed from the door panel. The two uppermost retainers do not
need to be removed in order to remove the door panel. Fig. 2
Read the rest of this entry »

• 0 Comments

The Police Upfitter’s Guide has been prepared with the assistance of service and engineering specialists to assist vehicle upfitters in achieving the highest standards of safety and quality in their products. This guide is divided into topics pertinent to upfitters of police vehicles. References are made to the 2008 Dodge Charger and Magnum Service Manual for appropriate service procedures, torques specifications, component separation clearances, and other standard information that is common with the unmodified vehicle.
Read the rest of this entry »

• 0 Comments

Installation: 2005 Dodge Charger or Magnum
1. Remove the 2 plastic covers that protect the front area under the hood (Fig. 1). They snap into or out of the vehicle.
2. Remove the 2 bolts that hold the hood latch assembly on and set it aside (do not disconnect the cables). Unplug the horn wire and place the wire out of the way (Figs. 1 & 2).
3. Mount speaker to bracket (Fig. 3).
4. Remove all the plastic rivets from the top of the front of the body of the vehicle, then pull the body toward the front of the vehicle (the body is flexible). Slide the 2 U-Nuts onto the support braces (Fig. 4) and place the bracket (with siren attached) on top of the U-Nuts. The front “ears” of the bracket rest on the two U-Nuts which clip onto the support braces (Fig. 4). The rear of the bracket will mount behind the hood latch assembly using the hood latch’s mounting hardware (Fig. 2).
Read the rest of this entry »

• 0 Comments

Subject: Radio With Six Disc CD Changer Does Not Recognize Loaded CD And Displays An “INITIALIZING” Message, CD Will Not Play, CD Cannot Be Ejected, Or Disc Icon Does Not Illuminate (Reprogram Radio)
Models:
2005-2006 Chevrolet Avalanche, Suburban, Tahoe
2005-2007 Chevrolet Colorado, Express, Silverado Classic, TrailBlazer
2005-2006 GMC Yukon, Yukon XL
2005-2007 GMC Canyon, Envoy, Savana, Sierra Classic
2005-2006 HUMMER H2 with Six Disc CD Changer Equipped Audio System (RPO UC6)
Read the rest of this entry »

• 0 Comments

Read all instructions before starting any work.
1. Remove the old exhaust system assembly from the vehicle. Lubricate the rubber isolators with WD-40, or a similar product, to aid in removal of the metal rod hangers.
2. Install DynoMax front exhaust x-pipe 54320. Finger tighten the inlet clamps.
3. Install DynoMax Super Turbo Mufflers 17662, right hand and left hand. Finger tighten the 2ı⁄₂” clamps that connect the mufflers to the x-pipe.
Read the rest of this entry »

• 0 Comments

The information contained in this TSB supersedes TSB No. ST001-06. • Applicability has been updated to include 2005 – 2006 model year Avalon and 2006 model year Highlander HV. • Production Change information has been removed. • The Introduction, Warranty Information, Parts Information, and Repair Procedure sections have been updated to reflect removal, lubrication, and reinstallation of the steering intermediate shaft instead of replacement. TSB No. ST001-06 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding.
Read the rest of this entry »

• 0 Comments

When any of the memory switches are pushed while the automatic drive positioner is operating When the adjusting switch for the driver s seat is turned on while the automatic drive positioner is operating When the memory switch 1 or 2 is not pushed and held for at least 1 second When the seat has been already moved to the memorized position When no seat position is stored in the memory switch When the automatic transmission selector lever is moved from P Park to any other position When the driver s door remains open more than 45 seconds and the ignition switch is not in the ON position The automatic drive positioner system can be adjusted and canceled For vehicles with navigation system see Vehicle electronic systems in the Display screen heater air conditioner and audio systems section of this manual For vehicles without navigation system see your NISSAN dealer Pre driving checks and adjustments
Read the rest of this entry »

• 0 Comments