suzuki sidekick timing marks search result
Removal Timing Belt(Esteem)
1. Disconnect negative battery cable. Remove right side engine under cover. Remove power steering and A/C compressor drive belts. 2. Remove A/C compressor and power steering pump with hoses attached, and secure out of way. Support engine from above or with floor jack under oil pan. Remove air cleaner case with air cleaner outlet hose. 3. From timing belt end of engine, remove engine mount and mounting bracket. Loosen water pump pulley bolts. Remove water pump drive belt and pulley. 4. Remove 5 crankshaft pulley-to-crankshaft bolts. Remove pulley. It is NOT necessary to remove crankshaft center bolt. Remove timing belt cover. See Fig. 1 . 5. Rotate crankshaft clockwise to align timing marks. See Fig. 2 and Fig. 3 . Stamped “E” on camshaft sprocket must point straight up. Loosen timing belt tensioner bolt and stud nut. Move tensioner away from belt, and hand tighten bolt and nut. See Fig. 4 . 6. If reusing old belt, mark belt with an arrow indicating direction of rotation for installation reference. Remove timing belt.
Read the rest of this entry »
Removal
1. Disconnect negative battery cable. Raise and support vehicle. Remove engine under cover.
2. Lower vehicle. Remove radiator coolant reservoir, and set aside. Remove electric cooling fan
and radiator shroud.
3. On Impreza and Forester, remove accessory drive belt cover. On all models, remove accessory
drive belts.
4. Hold crankshaft pulley stationary, and remove crankshaft pulley center bolt. Remove
crankshaft pulley. Remove timing belt covers.
Read the rest of this entry »
When installing the timing belt, be sure to align all alignment marks on the belt with corresponding marks on the sprokets. If incorrectly installed, interference between pistons and valves may occur.
Timing Belt Removal
1. Remove timing belt guide. (MT vehicles only)
2. If alignment mark (a) and/or arrow mark (which indicates rotation direction) on timing belt fade away, put new marks before removing timing belt as shown in procedures below.
Read the rest of this entry »
This timing belt installation is supported for Lexus 3.0L V6 – 1999-03 ES300. Removal (ES 300)
1. Raise and support vehicle. Remove right side front wheel. Remove right fender apron seal. Remove accessory drive belts. Lower vehicle. Disconnect engine coolant reservoir hose from water outlet. Disconnect ground strap connectors. 2. Remove engine moving control rod and engine mounting bracket No. 2 (right side), located near timing belt cover. Remove generator-to-engine bracket for access to timing belt covers. 3. Using Pulley Holder (09213-54015) or equivalent and Handle (09330-00021) or equivalent, hold crankshaft pulley. Remove crankshaft pulley bolt. Using puller, remove crankshaft pulley. Remove No. 1 and No. 2 timing belt covers and gaskets. See Fig. 1 . Remove Read the rest of this entry »
The steps of timing belt installation for this 1993 Mercury Villager LS.
Removal
1. Disconnect negative battery cable. Raise and support vehicle. Remove covers from below engine. Drain cooling system. Remove right front wheel and engine side cover. Remove accessory drive belts. Remove crankshaft pulley bolt and pulley. 2. Remove upper radiator hose and water inlet hose. Remove A/C compressor idler pulley and bracket. Remove water pump pulley. Remove upper and lower timing belt front covers. See Fig. 1 . 3. Temporarily install crankshaft pulley bolt so crankshaft can be rotated. Set cylinder No. 1 at TDC of compression stroke by rotating crankshaft until marks on camshaft sprockets align with marks on timing belt upper rear cover, and mark on crankshaft sprocket aligns with mark on front cover housing. See Fig. 2 . 4. Loosen timing belt tensioner nut. Release tension on belt. Remove timing belt. Check timing belt tensioner, spring and timing belt.
Read the rest of this entry »
For those of you that have not come across or had the privilege of working on the Ford 4.0L SOHC cam engine you are about to get a baptism in its proliferation in the timing components used. Now before you go off and wonder why I am even trying to tell you about these, know this there are none available in the aftermarket (or at least not that I was able to find). You can buy tensioners, guides and chains but gears are not available from the aftermarket and as you see the proliferation you will understand why. So you will either have to purchase them new from Ford or you are going to reclaim those that are not worn or damaged.
Read the rest of this entry »
Tools and supplies needed:
1. Basic hand tools as required for your particular camshaft and balancer bolts
2. Torque wrench
3. Pro Cam Lube (part #153 or #154) or suitable replacement
4. Camshaft Degree Kit (part #4796 including degree video)
5. Crankshaft Socket (part #4798 for Ford 302-351W, 429-460)
6. Thread locking compound
7. Engine repair manual for your particular engine
Read the rest of this entry »
Chevrolet Timing Chain Tools and Supplier needed: Kit Components
25 Dec
Posted by admin as Chevrolet
The following instructions begin after the timing cover and old timing set have been removed.
Installing the timing set and degreeing the camshaft will be easier if you loosen the rocker arms so that the camshaft can turn freely. You should be able to turn the camshaft by hand. Make sure that the engine mounting surfaces and your new timing set have been thoroughly cleaned with a good solvent. If you are using a timing set with three keyways, select the appropriate keyway for your camshaft timing specifications. COMP Cams ® recommends the standard timing position for most applications. This position uses the round or “O” timing and keyway marks. Standard Timing Location: This is the same as original O.E.M. setting. Use keyway and crankshaft gear tooth marked “O”.
Read the rest of this entry »
Installing the Distributor and Static Timing of the Chevrolet Inline 6
30 Dec
Posted by admin as Chevrolet
Following these procedures will guide you in correctly indexing the distributor assembly and initially setting the ignition timing advance.
1: The first step in this procedure is to insure that the #1 piston is brought to the top dead center (TDC) firing position. The firing position is TDC between the piston’s upward compression stroke and the subsequent downward power stroke. To achieve # 1 TDC firing position, perform either one of the following tasks.
Read the rest of this entry »
Camshaft timing belt must be replaced if cylinder head is to be removed or if drive gears, tensioner or coolant pump are to be replaced. Camshaft timing belts must be stored and handled with care. Always store a camshaft timing belt on its edge with a bend radius greater than 2.0″ (50 mm). DO NOT use a camshaft timing belt that has been twisted or bent double, as this will damage reinforcing fibers. DO NOT use a camshaft timing belt if debris other than belt dust is found in timing belt covers. DO NOT use a camshaft timing belt if partial engine seizure has occurred. DO NOT reuse a camshaft timing belt if mileage exceeds 45,000 miles. DO NOT use an oil or coolant contaminated timing belt (cause of contamination must be rectified).
Read the rest of this entry »
Categories
Archives
Cars PDF Document is proudly powered by WordPress - BloggingPro theme by: Design Disease