Engine, removing and installing Note: All cable ties opened or cut during engine removal must be reinstalled at the same locations. Remove engine without transmission toward the front. Drained coolant must be stored in a clean container for disposal or reuse. Always replace seals and gaskets. Do not open coolant circulation system.
Read the rest of this entry »

• 0 Comments

Tools needed: T30 Torx Bit, power drill, 15/64” drill bit, 10 mm socket, ratchet and short extension, stanley knife or tin snips, small clamp; optional: one caulk tube of silicone adhesive
BEFORE PAINTING – FIT BUMPER COVER AS FOLLOWS:
1. Remove the factory Air Dam by removing the five 10 mm hex bolts; discard the bolts and Air Dam.
2. Using the T30 Torx Bit and remove the two torx head bolts at each end of the factory painted upper bumper cover; save these bolts.
3. Using a stanley knive or tin snips, trim away approximately ž” of material from under the bottom edge of the factory upper bumper cover on each side at the area where the cover curves into the center bumper opening. This will allow clearance for the upper edge of the TMD Bumper Cover to slide up into this area. It is necessary to gently pull or pry out on the factory upper bumper cover to trim it.
Read the rest of this entry »

• 0 Comments

Prep Work And Check List
Clean the Surface of the Box sides on your truck with denatured alcohol or wax remover. It is IMPORTANT that the surface is clean so that our Box seal will adhere properly to the Truck box.

Install Rails And Seals
1. There are two rails. Put the rail with the 3rd leg hinge clamp (Fig.1) closest to the cab on the bed rail. Make sure the rail is as close as possible to the cab. Remove the blue paper. Push the rail down, then do the same for the other side.
2. To clamp the rail on the truck bed use a 5/16” socket, wrench or drill then tighten the screws on clamps. Be careful not to over tighten! (Fig 2.) You may use the preset spots on each rail.
Read the rest of this entry »

• 0 Comments

The 60-66 Chevy Truck Cab Cover is the finishing touch on your interior. The inner steel walls of the cab allow you to cover them in fabric tuck the edges under the door and window seal rubber and trim off the roof with the headliner for a professionally finished look.
Read the rest of this entry »

• 0 Comments

This pdf covers the removal & installation the timing case cover for Chevrolet S10 Pickup.
Removal
1. Disconnect negative battery cable. Remove P/S reservoir from radiator shroud. Remove upper fan shroud. Remove serpentine belt.
2. Remove generator with brackets and lay aside. Using Hub Puller (J-24420-B), remove crankshaft pulley hub. Remove oil pan. See OIL PAN. Remove front timing case cover bolts, and cover.
3. Using large screwdriver, remove crankshaft front seal. DO NOT distort timing gear cover during seal removal.
CAUTION: To prevent oil leakage, coat crankshaft pulley hub keyway with RTV sealant before installation.
Read the rest of this entry »

• 0 Comments

The new Audi A6 – the most progressive vehicle takes the lead Design and performance are the main driving elements on its way to the top position. Furthermore, the new Audi A6 embodies the consequent continuation of the familiar Audi brand values, sports appeal, progressiveness and intrinsic quality, which are evident in the fourth generation of this sporty business limousine.
Read the rest of this entry »

• 0 Comments

The engine control unit has a self-diagnosis capability. Before carrying out repairs and fault finding the fault memory must be interrogated. The vacuum hoses and connections must also be checked (unmetered air).
- Fuel hoses in engine compartment must only be secured with spring-type clips. Clamping-type or screw-type clips must not be used.
Read the rest of this entry »

• 0 Comments

This B&M Short Throw Shifter has been designed to work on most 1996-2000 Audi A4, 2000 Audi S4, 2000 Audi A6, and 1996-2000 Volkswagen Passat models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
Read the rest of this entry »

• 0 Comments

Powerchip technology enhances your Audi to its ultimate level, delivering faster, smoother acceleration in all driving conditions. Whether you enjoy a leisurely weekend cruise or a hard racetrack drive – there is no easier and more effective way to release the potential from your S4 4.2 V8.

The following information is an overview of the performance the Powerchip will deliver. If you have any questions, your Power Consultant will assist you as best as possible. We look forward to giving you the best performance possible from your Audi.
Read the rest of this entry »

• 0 Comments

Common Problems
1. I am having trouble connecting with an ‘02 Audi A4.
This vehicle does pose connection issues with most aftermarket tools. Please continue to retry the connection.
2. I am having trouble getting good data rates on a specific controller.
Audi/VW consolidated sensors into groups. Some sensor groups can update at slower rates then others. Typically, this is text-based sensors on non-critical models like Telephone or Climate control. To resolve this select only those sensors that are important to you until you reach a saturation point for the data throughput.
Read the rest of this entry »

• 0 Comments