RGB Module Connections & Controls
The NV_RGB_X Video Interface is capable of both single video and dual video modes of operation. For dual video mode, the optional remote control pad is recommended for switching between the video inputs on the module.
Installation With Plug And Play Factory Harness
Read the rest of this entry »

• 0 Comments

These instructions provide information for the installation of the 60510 Fuel Injection Wire Harness Kit. The contents of these instructions are divided into major Sections, as follows:
1.0 Introduction
2.0 About These Instructions
3.0 Tools Needed
4.0 Pre-Installation and Harness Routing Guidelines
5.0 General Installation Instructions
6.0 60510 & 60511 Fuel Injection Harness Kit
7.0 Start Up
8.0 Trouble Shooting Instructions and Trouble Codes
Read the rest of this entry »

• 0 Comments

Along with the increase of electronic devices used in automobiles, the use of wiring harnesses for power and signal systems on board is growing remarkably. In these circumstances, the electromagnetic interference (EMI) generated by the power system should cause troubles on signal systems and other chassis-mounted electronic devices. Wiring harnesses act as the direct transmission lines of EMI, so the shielding has become an essential element of power wiring harness system. Generally, braided shield cables and shielded connectors have been used as the EMI shielding measures on the wiring harnesses. Such measures, however, resulted in the increase in cost and size of wiring harnesses. This paper describes the development of a low-cost shielded construction for high-voltage wiring harnesses applied in Toyota’s hybrid electric vehicle (HEV), new Prius.
Read the rest of this entry »

• 1 Comment

WIRING INFORMATION 1989 Nissan 240SX WIRE COLOR LOCATION 12V CONSTANT WIRE WHITE Ignition Harness 12V IGNITION WIRE BLACK/RED Ignition Harness 12V ACCESSORY WIRE BLUE Ignition Harness STARTER WIRE BLACK/YELLOW Ignition Harness SECOND STARTER WIRE BLACK/WHITE Ignition Harness PARKING LIGHTS (+) RED/BLUE Back Of Dash Dimmer Switch Or Harness In Driver’s Kick Panel POWER DOOR LOCK (Interrupt wire using a ORANGE BLACK Harness In Drivers Kick Panel Or Harness relay) Coming Into Vehicle From Driver’s Door POWER DOOR UNLOCK (Negative trigger) Same wire as lock Harness In Drivers Kick Panel Or Harness Coming Into Vehicle From Driver’s Door
Read the rest of this entry »

• 0 Comments

1990-1993 Wiring Chart Circuit LG/W GY/W R/W R/Y P/W LB R/Y GY BK/LB, PK/LG BK/Y T/Y Not Used LB/R BK Circuit Function Left Turn Indicator Hi Beam Indicator Coolant Temperature Sender Feed 12V Input1 Check Brake Indicator Feed Low Coolant Indicator Feed 12V Input1 Check Oil Indicator Feed Malfunction Indicator Lamp (MIL) Feed Air Bag Indicator Tachometer Feed Not Used Illumination Feed Ground Pin Number Circuit Not Used R/LG Not Used Not Used Not Used Not Used R/Y W/R BK Y/W LB/R W/LB DG/LG LG/R Circuit Function Not Used Ignition Switch Not Used Not Used Not Used Not Used 12V Input1 Oil Pressure Gauge Feed Ground Fuel Gauge Feed Illumination Feed Right Turn Indicator Fasten Belts Indicator Battery Indicator Feed
Match to same colors as the 1987-1989 harness.
Read the rest of this entry »

• 0 Comments

Installation Procedure:
1. Remove the PLASTIC BUMPER FASCIA mounted to the bottom of the front bumper. For the Avalanche, remove the entire plastic bumper. Disconnect the fog lamp electrical harnesses prior to removing the bumper. Note: The airfoil/bumper will need to be permanently removed or notched to accommodate the undercarriage assembly.
2. Remove and discard the three bolts that secure each tow hook to the truck frame. The tow hooks should remain in the same position.
3. Align the undercarriage mount pockets (at each end of the PUSH BEAM WELDMENT) with the tow hook mounting brackets on the vehicle. Note: Use a floor jack to help facilitate the installation procedure.
Read the rest of this entry »

• 0 Comments

1. For the Dakota: Remove bumper, retaining all OEM fasteners for reinstallation.
Proceed to Step 2.
For the Durango: Prior to removing the bumper, cut and remove the center portion of the bumper and air dam as shown in the photo below. Retain the cut out section of the air dam to fabricate an air deflector in Step 8. Remove the remaining bumper assembly, retaining all OEM fasteners for reinstallation.
2. Clamp the driver-side mount plate to the outside of the driver-side vehicle frame. Make sure the mount alignment tab fits up against the back of the vehicle frame front plate, and the front and rear plate stiffeners are snug against the bottom of the frame. When positioned correctly, mount plate holes align near the center of the vehicle frame.
Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2003 Lincoln Aviator WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE YELLOW Ignition Harness STARTER WIRE DK.GREEN Ignition Harness IGNITION WIRE RED/LT. GREEN Ignition Harness ACCESSORY WIRE GRAY/YELLOW Ignition Harness POWER DOOR LOCK (-) PINK/YELLOW Harness In Driver’s Kick Panel POWER DOOR UNLOCK (-) PINK/LT. GREEN Harness In Driver’s Kick Panel • The factory module that controls the door locks shuts down to conserve power. When installing an aftermarket keyless entry system, hook up dome light supervision and program the aftermarket system for a double-pulse unlock to “wake up” the module and unlock the doors. PARKING LIGHTS (+) BROWN Headlight Switch DOOR TRIGGER (+) BLACK/LT. BLUE Harness In Driver’s Kick Panel or Courtesy Light Under Dash DOME LIGHT SUPERVISION USE DOOR TRIGGER REAR HATCH TRIGGER COMMON WITH DOORS REAR HATCH RELEASE (+) PURPLE/YELLOW OEM Read the rest of this entry »

• 0 Comments

Supplemental Restraint System SRS (a) Failure to carry out procedures listed below could result in possible deployment of airbag, personal injury, or unnecessary repairs to SRS. (b) Turn the key switch to the LOCK position. (Fig. 1) (c) Remove the key from the ignition switch. (d) Disconnect the negative battery cable. (Fig. 2) (e) Never use a voltmeter to trouble shoot any of Accidentally probing the connectors to the SRS can lead to deployment of the airbag. (Fig 3) (f) SRS wire harness loom/cover is bright yellow in color.
Read the rest of this entry »

• 0 Comments

WIRING INFORMATION: 2002 Chevy Trailblazer WIRE WIRE COLOR WIRE LOCATION 12V CONSTANT WIRE RED and RED/WHITE Ignition Harness STARTER WIRE YELLOW Ignition Harness IGNITION WIRE PINK Ignition Harness SECOND IGNITION WIRE WHITE Ignition Harness ACCESSORY WIRE ORANGE Ignition Harness SECOND ACCESSORY WIRE BROWN Ignition Harness KEYSENSE WIRE (-) LT.GREEN Ignition Harness POWER DOOR LOCK On these vehicles, door locks are controlled by a data bus system. This requires interfacing the door locks in several locations (each of the front doors, the rear hatch, and the fuse box under POWER DOOR UNLOCK the rear seat) or using a databus interface module Read the rest of this entry »

• 0 Comments